![background image](http://html.mh-extra.com/html/olympia/g-3650/g-3650_operating-manual_732602011.webp)
11
R
Changing the Blade
Note
: Before changing the blade, refer to the
note in Section
Adjusting the Blade
.
A spare blade and tools with which to change
the blade are available in the spare part and
tool compartment (14).
1. Loosen the screw securing the spare part
and tool compartment (15).
2. Remove the tools (hex key, assembling
aids), spare blade with cut protection and
separate cut protection for the old blade.
3. Release the lock (1) and move the guillo
tine arm (1) downwards using the handle
(4).
4. Press the lock (11) inward.
5. Open the safety guard (13).
6. Loosen the screws (20) in the blade guard
(19) and remove it.
7. Loosen the screws 2 and 5 (counting from
the left) of the six screws in the fastening
rail (18) and assemble the assembling aid
in the free screw holes.
8. Loosen the other screws in the fastening
rail (18).
9. Use the assembling aid to carefully re
move the fastening rail (17) and blade (16).
Attention
: Risk of injury! The guillotine
blade is very sharp! Never reach in
towards or take hold of the guillotine blade.
10. Carefully assemble the cut protection tak
en from the spare part and tool compart
ment (14) on the old blade (16). Remove
the old blade (16) from the fastening
rail (17) and install the new blade, properly
aligned, on the fastening rail (17) (pay at
tention to the holes) .
11. Remove the cut protection carefully from
the new blade (16).
12. Assemble the assembling aid in the screw
holes 2 and 5 (counting from the left) in the
fastening rail (17) and install the rail back
in the device.
13. Insert the screws (18) in the free screw
holes in the fastening rail (17), in succes
sion, and tighten them carefully.
14. Remove the assembling aids and insert
the remaining screws (18) for the fastening
rail (17) in the screw holes.
15. Tighten all the screws (18) for the fasten
ing rail (17) evenly.
16. Replace the blade guard (19) back on the
device and tighten the screws for the blade
guard (20) firmly.
17. Place the tools and cut protection in the
spare part and tool compartment (14) and
tighten the screw securing the spare part
and tool compartment (15).
Adjusting the Blade
If the cut produced by the blade is not clean,
you can adjust the position of the blade.
1. Move the guillotine arm to its bottom posi
tion. Draw the lock of the guillotine arm (1)
towards you and press the handle (4) of
the guillotine arm (6) downwards. Press
the lock inwards. The guillotine arm is then
locked in its bottom position.
2. Loosen and remove the screw (15) to open
the spare part and tool compartment (14).
3. Remove the hex key contained in the
spare part and tool compartment (14).
4. Insert the hex key in the rear screw
hole (12). The insertion aid indicates that
the hex key must be inserted angled at
about 15 degrees to the right . Insert the
hex key in the other screws (12) in the
same was in order to reach the respective
screw with the hex key.
5. Turn the blade adjustment screws (12)
clockwise in the areas in which the cut is
not clean. Take the utmost care when
making the adjustment. Test the quality of
the cut during the process.
Содержание G 3650
Страница 1: ...Hebelschneider G 3650 Guillotine G 3650 R D Bedienungsanleitung G Operating Manual G 3650 R ...
Страница 14: ......