background image

 

Date 

22/4/2021 

Document number 

921100400_09_005 

Page 

17 of 71 

 

 

17 / 71 

Figure2-21.Conventional sirens

 

By selecting “

TASKS

” option, the screen on the right appears.

 

The first line shows the name of the task (editable via pc software). 
The  second  line  shows  the  function  logic  (AND  /  OR)  of  the  task. 

ZONES NUMBER

” 

shows the total number of zones that have been 

selected to trigger this task. 

Navigate between the tasks with up/down keys. If no tasks have been 

set the screen will display a “

NO DATA

” message.

 

Figure2-22.Tasks

 

By selecting “

NETWORK PANELS

” option, the screen on the right 

appears. 

The available options are valuable only for panel networks. The first 

option  “

ACTIVE

 

ADDRESSES

”  shows  the  detected  panels  in 

network and is only available to the Master control panel.  

The  second  option  “

PANELS  IN  TEST

”  shows  which  of  the 

connected panels in the network are in test mode.  

The third option “

NAME

” will display the name of the panel (editable 

via PC software or web interface), the network address of the panel 
and its serial number.  

 

Figure2-23.Network panels

 

By selecting “

ETHERNET ADAPTOR

” option, the screen on the right 

appears. When “

ETHERNET PCB

” is active, the value will be YES, 

else is NO. When the Ethernet adaptor is activated, the IP Address 
(IPv4)  of  the  control  panel  will  be  displayed,  as  well  as  the  MAC 
Address of it. 

 

 

 

Figure2-24.Ethernet adaptor

 

By selecting 

TECHNICIAN INFO

” option, the s

creen on the right appears.  

The OLYMPIA ELECTRONICS S.A. contact info is displayed by default.  

This information can be changed via  PC software or  web interface  by the 

installer,  in  order  to  provide  the  desired  company’s  name  and  telephone 

number.  

This  information  must  match  to  the  contact  that  is  responsible  for 
maintenance and repairs of the fire detection system. 

 

Figure2-25.Technician info

 

By  selecting 

ANNUAL  CHECK  DATE

”  option,  the  next  scheduled 

maintenance  date  is  displayed.  In  order  for  the  date  to  be  displayed,  the 
installer must enable annual check warning through technician menu, else 

“INACTIVE” message is displayed.

 

 

Figure2-26.Annual check date

 

Содержание BSR-1000








































































Отзывы: