OLT SunShed Garden Shed SSGS1212-FJ-METAL Скачать руководство пользователя | Manualshive

Страница: 38 / 45

background image

79.

Attach

Narrow Wall Trims

around the Sunshed. Narrow trims are used where wall panels come

together and leave a seam.

Note:

the Narrow Trim on the Short Wall side is only 79” long. Attach

with 8 - 1 1/2” finishing nails per piece.

80.

Locate all

Ridge Caps

for Polygal Panels (3 Mid / 2 Outside / 2 Center). Starting from the out-

side, position both 5 1/2” wide caps so outside edge is aligned with edge of batten and Cap end slides
under roof. Use a straight edge to aid in alignment.

See below.

When correctly aligned, attach Caps

to center of outside rafter with 6 - 1 1/2” finishing nails. Ridge Cap has nailing strip attached.

Mid (3)
2 1/2” wide

Outside (2)
5 1/2” wide

Center (2)
3 1/2” wide

Ridge Cap slides under Roof Panel and has nailing strip attached to
outside underside of it. Strips allows facia to attach easier when they
are nailed.

Cap overhangs rafter
end by approx 1/2”

Batten and
cap evenly
aligned.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 38

«
...
36
37
38
39
40
...
»

Содержание SunShed Garden Shed SSGS1212-FJ-METAL














































Отзывы:

Нет отзывов

Похожие инструкции для SunShed Garden Shed SSGS1212-FJ-METAL

Бренд: Yardline Страницы: 97

Бренд: Palmako Страницы: 44

Бренд: Palmako Страницы: 27

Бренд: Palmako Страницы: 30

Бренд: Palmako Страницы: 44

JUTLAND 18 2320 IL2320 R1 F0

Бренд: Gartenpro Страницы: 34

Бренд: Palmako Страницы: 103

Бренд: Palmako Страницы: 58

shedmaster GABLE 8' x 12'

Бренд: Backyard Products Страницы: 55

Бренд: Mercia Garden Products Страницы: 9

Бренд: Palmako Страницы: 76

Бренд: Holman Страницы: 9

02BRAM0806-V3-PEFC

Бренд: Mercia Garden Products Страницы: 9

Бренд: HAMPTON BAY Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды