OLT SunShed Garden Shed SSGS1212-FJ-METAL Скачать руководство пользователя | Manualshive

Страница: 16 / 45

background image

27.

Position

Front Top Plates

on top of wall framing so they are flush on the inside with 2x3 wall

frame. There are 2 Front Top Plates. Together, the plates should be centered evenly on the wall left to
right. Attach by screwing down into top wall framing with

4 - 2” screws

per Plate.

Angle cut
on 1 end.

Top Plates

Top Plates should
be flush with inside
of wall framing.

26.

When all walls are attached

together, check alignment with the
floor. Bottom wall framing should
sit flush with outside of floor joists.
When positioned correctly, fasten
bottom wall plates to floor using

4 - 2 1/2” screws

per wall panel.

Confirm 32” wide door opening
at bottom.

Bottom Wall
Framing

Important:

If walls are not lining

up and appear higher or lower than
each other, please check the level
of your floor. You may need to
make slight adjustments before
proceeding.

Optional:

Caulking seams will

help prevent moisture from
entering your shed. Caulking
is included to complete polygal
Windows only. Additional
Caulking may be required.

Caulking

Angle

screws into perimeter

Floor Joists.

32”

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 16

«
...
14
15
16
17
18
...
»

Содержание SunShed Garden Shed SSGS1212-FJ-METAL














































Отзывы:

Нет отзывов

Похожие инструкции для SunShed Garden Shed SSGS1212-FJ-METAL

Бренд: OLT Страницы: 44

Бренд: Waltons Страницы: 9

Heartland VALUE Series

Бренд: Backyard Products Страницы: 52

Бренд: Palmako Страницы: 50

Бренд: Palmako Страницы: 104

Бренд: Palmako Страницы: 72

Бренд: Palmako Страницы: 103

Бренд: Vision Страницы: 15

Бренд: Homestyles Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды