background image

14.

 

Position 

2D

 

- Door Header - Short

 on top 

of wall stud so it is flush on the outside with the 
wall siding. Attach by screwing down into top wall 
framing with 

3 - 3” Screws

.

Parts (Step 14 - 15)

 

2D - Door Headers - Short 

(2” x 3 1/2” x 26 1/4”) 

x 2

 

2E

 

- Door Header - Long

 

(2” x 3 1/2” x 84”) 

x 1

 

Hardware (Step 14 - 15) 

S4

 

- 3” Screws

  

x 10 total 

S2

 

- 1 1/4” Screws

  

x 4 total

Step to front  
and top.

Align flush 
outside with 
wall siding.

15.

 

Attach 

2D

 

- Door Header - Short

 to other side. Position and attach 

2E

 

- Door Header - Long 

between short door headers. The Long Door Header has an aluminum strip attached to the back for added 
support. Attach by screwing down into wall framing with 

2 - 3” Screws 

per side. Fasten aluminum strip to 

short headers with 

2 - 1 1/4” Screws

 per side.

Aluminum strip on back 
of Long Door Header

Door Header 
overhangs 
inside wall 
framing by 1/2”

  Toll Free 1-888-658-1658              www.outdoorlivingtoday.com        [email protected]

Page 13

Содержание SpaceSaver SS124-SLIDER-PLY-AK




































Отзывы: