OLT GS124-SLIDER-CEDAR-AK Скачать руководство пользователя страница 9

Страница: 9 / 42

Position

- Floor Runners - Short

on each

side of the completed floor frame. Runners should
be flush with corners but not overhanging. Attach
with

4 - 2 1/2”

Screws

per Runner.

Parts

1C - Floor Runners - Short

(1 1/2” x 3 1/2” x 45 1/2”)

x 2

Hardware

- 2 1/2” Screws

x 8 total

Align

1CC - Floor Runners - Long

evenly spaced as shown above and

flush with the back of the Floor Frame. On the front, Runners will extend 2”
past the Floor Frame to provide support for the Sliding Door Track later in
the Assembly. Attach with

4 - 2 1/2”

Screws

per Runner.

With Floor Runners attached, carefully flip the floor over and place on your
foundation.

Caution -

Be careful when laying floor down not to bend or twist

floor.

Note:

Having a level foundation is critical. Choosing a foundation will

vary between regions. Typical foundations can be concrete pads or patio
stones positioned underneath the floor runners.

Position

1D - Plywood Floor

on top of completed floor frames.

Plywood will sit slightly inset from outside of floor frame.

Parts

1D -

Plywood Floor

(5/8” x 45 3/8” x 70 5/8”)

x 2

Note:

Plywood is cut slightly

smaller than floor framing.
Keep plywood seams tight.

Parts

1CC - Floor Runners - Long

(1 1/2” x 3 1/2” x 47 1/2”)

x 5

Hardware

- 2 1/2” Screws

x 20 total

Long Floor Runners overhanging Floor Frame on front.

Floor Runners flush with Floor Frame on back.

Concrete Slab
Foundation

Front

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 9

Содержание GS124-SLIDER-CEDAR-AK











































Результаты поиска

Содержание GS124-SLIDER-CEDAR-AK

Отзывы:

Похожие инструкции для GS124-SLIDER-CEDAR-AK

Бренды по названию

Популярные бренды

OLT GS124-SLIDER-CEDAR-AK, Инструкция по сборке

Результаты поиска

Содержание GS124-SLIDER-CEDAR-AK

Отзывы:

Похожие инструкции для GS124-SLIDER-CEDAR-AK

Бренды по названию

Популярные бренды