OLT CLA128-SLIDER-METAL-ES Скачать руководство пользователя страница 12

Страница: 12 / 44

13.

For each

Solid Wall Panel

, carefully lay panel

face down. Position and attach a

Bottom Wall

Plate

to bottom of wall studs of each wall panel with

3 - 2 1/2” Screws

. Position so plates are flush with

framing. Wall siding will overhang bottom wall plate.

Parts

Solid Wall Panels

(45 1/2” x 75”)

x 7

Bottom Wall Plates

(1 1/2” x 2 1/2” x 45 1/2”)

x 7

Hardware

- 2 1/2” Screws

x 21 total

14.

Starting at Rear Corner, position a Solid Wall Panel

on top of plywood floor. The Wall Panel bottom framing
will sit flush with plywood. Wall siding will overhang the
floor. The Rear Wall panels will sit flush at the end of the
plywood floor with the side wall panels sandwiched
between them

Note:

Siding will overhang the floor by approximately

4 1/2”.

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]

Page 12

Pilot Hole

first.

Bottom Wall Plate

Important:

Pilot hole ALL 2x3 Wall

Studs with 1/8” drill bit prior

to screwing. This will make it

much easier to attach

together.

Side of Shed

1st Rear
Wall Panel

Front of Shed

Important -

Make sure all walls are aligned

in their upright position. If not, water may
leak into your shed. Unsure if panel is
facing up or down? Wall siding overhangs
the base of the wall.

1st Rear Wall Panel

side of shed

2x3 wall frame

Flush with
Floor Framing

4 1/2” overhang

Содержание CLA128-SLIDER-METAL-ES













































Результаты поиска

Содержание CLA128-SLIDER-METAL-ES

Отзывы:

Похожие инструкции для CLA128-SLIDER-METAL-ES

Бренды по названию

Популярные бренды

OLT CLA128-SLIDER-METAL-ES, Инструкция по сборке

Результаты поиска

Содержание CLA128-SLIDER-METAL-ES

Отзывы:

Похожие инструкции для CLA128-SLIDER-METAL-ES

Бренды по названию

Популярные бренды