Olsen OLSSC-075 страница 29 Скачать руководство пользователя

Страница: 29 / 72

9.1 Fill Boiler With Water And Purge Air

Fill boiler with potable water.

•

Fill boiler and system piping with water (or antifreeze-

•

water solution, if used). See antifreeze information

page 11. Purge air from boiler using air vent. Purge

air from system piping.
Inspect system piping and boiler connections. Repair

•

any leaks immediately.

9.2 Fill Condensate Trap with Water

Disconnect collet clip from condensate hose barb. See

•

fi gure 9-1.
Disconnect tubing below from hose barb.

•

Pour approximately 2 cups (473 ml) of water into

•

condensate drain.
Reconnect tubing to hose barb with collet clip. See

•

fi gure 9-1.

9 - START UP PROCEDURE

9-1 Condensate Drain Assembly

1. Disconnect collet clip from

hose barb and fi ll Condensate

trap with water.

NOTICE

IMPORTANT: Condensate trap must be manually

fi lled with water at initial start up.

2. Reconnect hose to hose

barb with collet clip before

starting boiler.

Содержание OLSSC-075









































































Результаты поиска

Содержание OLSSC-075

Отзывы:

Похожие инструкции для OLSSC-075

Бренды по названию

Популярные бренды

Olsen OLSSC-075, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание OLSSC-075

Отзывы:

Похожие инструкции для OLSSC-075

Бренды по названию

Популярные бренды