Oliver 797-32N Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 54

Oliver 797-32N Скачать руководство пользователя страница 4

797-N BREAD SLICER

0797S20021

1-1

SAFETY INSTRUCTIONS

WARNING

VARIOUS SAFETY DEVICES AND METHODS OF GUARDING HAVE BEEN

PROVIDED ON THIS MACHINE. IT IS ESSENTIAL HOWEVER THAT THE MACHINE

OPERATORS AND MAINTENANCE PERSONNEL OBSERVE THE FOLLOWING

SAFETY PRECAUTIONS. IMPROPER INSTALLATION, MAINTENANCE, OR

OPERATION OF THIS EQUIPMENT COULD CAUSE SERIOUS INJURY OR DEATH.

1. Read this manual before attempting to operate your machine. Never allow an

untrained person to operate or service this machine.

2. Connect the machine to a properly grounded electrical supply that matches the

requirements shown on the electrical specification plate and follow all specifications
of local electrical codes.

3. Disconnect and lock-out the machine from the power supply before cleaning or

servicing.

4.  Check and secure all guards before starting the machine.

5.  Observe all caution and warning labels affixed to the machine.

6.  Use only proper replacement parts.

7.  Do not wear loose fitting clothing or loose hair when working near this machine.

Shirt tails should be tucked in.

8. Wear proper, personal, protective, safety equipment.

9. Keep Hands away from the moving parts of this machine while it is in operation.

10. In addition to these general safety instructions, please follow the more specific safety

instructions in the rest of this operating instruction manual.

WARNING

DO NOT USE FOR OTHER THAN ORIGINALLY INTENDED PURPOSE.

«
...
2
3
4
5
6
...
»

Содержание 797-32N























































Отзывы:

Нет отзывов