manualshive.com logo in svg

Oliver 797-32N, Инструкция по эксплуатации, Страница: 3 / 54

Поделиться
Скачать
Oliver 797-32N Скачать руководство пользователя страница 3

 

797-N BREAD SLICER

 

0797S20020  

0-2 

 

INDEX (Continued) 

 

REPLACEMENT PARTS SECTION  (Continued) 

 
 

           Section Description

                                 

Document No.

                      

Page No. 

 

SLICE PARTS & HOLDDOWN ------------------------------- 0797S20030 -------------------------- 10-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

10-1 

 

Parts List ---------------------------------------------------------------------------------------------- 10-2 

 
32 INCH GRAVITY INFEED CHUTE ------------------------ 0797S20031 -------------------------- 11-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

11-1 

 

Parts List ---------------------------------------------------------------------------------------------- 11-2 

 
48 INCH GRAVITY INFEED CHUTE ------------------------ 0797S20032 -------------------------- 12-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

12-1 

 

Parts List ---------------------------------------------------------------------------------------------- 12-2 

 
32 INCH COMBINATION INFEED CHUTE ---------------- 0797S20058 -------------------------- 13-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

13-1 

 

Parts List ---------------------------------------------------------------------------------------------- 13-2 

 
STANDARD OUTFEED ---------------------------------------- 0797S20033 -------------------------- 14-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

14-1 

 

Parts List ---------------------------------------------------------------------------------------------- 14-2 

 
DRIVEN PULLEY ------------------------------------------------ 0797S20034 -------------------------- 15-1 
 Drawing 

----------------------------------------------------------------------------------------------- 

15-1 

 

Parts List ---------------------------------------------------------------------------------------------- 15-2 

 
SINGLE PHASE ELECTRICAL ------------------------------- 0797S20035 -------------------------- 16-1 
 

Wiring Diagram --------------------------------------------------------------------------------------16-1 

 Drawing 

----------------------------------------------------------------------------------------------- 

16-1 

 

Parts Lists -------------------------------------------------------------------------------------------- 16-2 

 
 THREE PHASE ELECTRICAL ------------------------------- 0797S20036 ------------------------- 17-1 
 

Wiring Diagram ------------------------------------------------------------------------------------- 17-1 

 Drawing 

----------------------------------------------------------------------------------------------- 

17-1 

 

Parts Lists -------------------------------------------------------------------------------------------- 17-2 

 
WARRANTY -------------------------------------------------------  GEN 040228 
 
WARRANTY PROCEDURE -----------------------------------  GEN 040226 
 
RETURNED PARTS POLICY --------------------------------  GEN 040227 
 
 
 

 
 
REV. 3/2/04 

Содержание 797-32N























































Отзывы:

Нет отзывов