Oliver 797-32N Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 54

Oliver 797-32N Скачать руководство пользователя страница 23

797-N BREAD SLICER

0797S20026

6-6

Changing the Blades

WARNING

ALWAYS DISCONNECT THE SLICER FROM THE POWER SUPPLY BEFORE

ATTEMPTING ANY TYPE OF MAINTENANCE TASK.

CAUTION

THE BLADES ARE EXTREMELY SHARP. ALWAYS HANDLE THEM WITH CARE.

NOTE

DO NOT INTERCHANGE THE TWO BLADE FRAMES. REPLACE THE BLADE

FRAME TO THE SAME SIDE OF THE MACHINE AS IT WAS TAKEN FROM

NOTE

WHEN CHAINGING BLADES FIRST NOTE THE DIRECTION THE SHARPENED

EDGES ARE FACING ON THE BLADE FRAME. THEY ARE FACING UP ON ONE

FRAME AND DOWN ON THE OTHER. DO NOT CHANGE THIS DIRECTION.

Place the blade frame on a flat surface. You may use the special knife tool, shown in
the illustration on the next page, or use a common set of pliers to depress the spring-
loaded pin holding each knife. This will reduce the tension on the knife so that it may be
easily removed.

In the illustration on the next page you can see the use of the knife tool. It is inserted
into the blade frame on the spring-loaded pin end and then by lifting up on the tool it will
deflect the pin reducing the tension on the knife. Once this has been done the knife can
be carefully removed.

Rev. 2/15/05

«
...
21
22
23
24
25
...
»

Содержание 797-32N























































Отзывы:

Нет отзывов