Oliver 4275C Скачать руководство пользователя страница 68

68 | 

Page 

Oliver Machinery 

4275C Jointer 

Warranty and Service 

Oliver Machinery makes every effort to assure that its equipment meets the highest possible standards 

of quality and durability. All products sold by Oliver Machinery are warranted to the original customer to 
be free from defects for a period of two (2) years on all parts excluding electronics and motors which are 

warranted for one (1) year from the date of shipment. Oliver Machinery’s obligation under this warranty 

shall be exclusively limited to repairing or replacing products or parts or components, at its sole option, 
determined by Oliver Machinery to be defective. Oliver Machinery shall not be required to provide other 
form of indemnity or compensation including but not limited to compensatory damages. 

 
This warranty does not apply to defects due to direct or indirect misuse, abuse,  negligence, accidents, 

unauthorized repairs, alternation outside our facilities, lack of maintenance, acts of nature, or items that 
would normally be consumed or require replacement due to normal wear and tear. 

 

OTHER TERMS

 

To  obtain  and  exercise  the  warranty  right,  please  call  800-559-5065  or  fill  out  warranty  request  form 

online at 

www.olivermachinery.net

. 

Warranty parts are shipped via Parcel or Ground. Additional charges will occur and charge to customers 

if express shipping is required. 

 

DISCLAIMER

 

Under  no  circumstances  shall  Oliver  Machinery  be  liable  for  death,  personal  or  property  injury,  or 

damages arising from the use of its products. 

Oliver  Machinery  reserves  the  right  to  make  changes  without  prior  notice  to  its  products  to  improve 

function or performance or design. 

 

FOR MORE INFORMATION

 

If you need assistance or have questions beyond what is covered in the scope of this warranty information, 

please call 800-559-5065 or email us at 

[email protected]

. 

Содержание 4275C







































































Отзывы: