Oliver 4040 Скачать руководство пользователя страница 11

9. Set the blade 45

 to the table by turning the 

blade tilting handwheel counter-clockwise as 

far as it will go.  Place a combination square

on the table and check to see that the blade

is at a 45

��

angle to the table.

10. If the blade  is  not  45

,  remove  raising  and 

lowering handwheel  by  unscrewing  the 

handwheel  lock  and  loosening  the two set

screws in  the  handwheel  hub,  as  shown  in 

Figure 13.

11. Loosen  hex  nut  (A,  Figure  13)  and turn

adjusting stop bolt (B, Figure 13) on the front

trunnion in, or out.  The adjusting stop screw

should stop against  the  front  trunnion 

bracket when blade is 45

��

to table. 

12. Tighten  the  hex  nut  (A,  Figure  13)  while 

holding the adjusting stop bolt (B, Figure 13) 

to keep it from moving. 

13. Check the accuracy of the pointer and adjust 

if necessary.    It  should  read  45

  on  the 

angle scale. 

Leveling Table Insert 

Adjust the  table  insert  flush  with  the  table  by 

turning four leveling  screws  (C,  Figure  14). 

Place  a  straight  edge  across  the table and

insert.  Raise the insert until it just touches the

straight edge. Check  both  the  front  and  rear 

section of the insert. 

Splitter and Blade Guard Assembly

1.

Disconnect saw from power source.

2. Remove table insert by loosening the screw

at  the  front  of  insert.    Pull  up and towards

you to release the rear clip.

3. Thread blade guard shaft (D, Figure 15) into

rear trunnion through opening at rear of saw. 

Use the flat  detent  at  the  end  of  shaft  to 

tighten blade guard shaft. 

4. Place bracket assembly (E, Figure 15) on to 

the shaft and thread a M8x35 hex head bolt 

and a M8 lock washer (F, Figure 15) into the

bracket.

5. Thread  the  guard  support  assembly  (G,

Figure 15) into the bracket. 

11

Содержание 4040
























Отзывы: