Okolab H301-PI-736-160x110 Скачать руководство пользователя страница 7

Страница: 7 / 17

H301-PI-736-160x110

User Manual

REV 03

www.oko-lab.com

Distance between focal plane

and upper side of the glass

lid without the chamber riser

Distance between focal plane

and upper side of the glass

lid with the chamber riser

Chamber top view

H301-INJECTION LID

Figure 6. H301-PI-736-1 H301-INJECTION-LID

3.4

Laser Interlock Lid

The Laser Interlock Lid is a heated glass lid with a safety switch connecting to the laser controller. It automatically

turns the laser off when the lid is lifted. NOTE: Compatible with sample holder 1x35 ONLY. The Laser Interlock Lid is

placed onto the chamber (NO SCREWS or TOOLS are necessary).

Figure 7 shows chamber dimensions with the Laser Interlock Lid (with and without chamber riser).

Distance between focal plane

and upper side of the glass

lid without the chamber riser

Distance between focal plane

and upper side of the glass

lid with the chamber riser

Chamber top view

H301-LASER-INTERLOCK LID

Figure 7. H301-PI-736-1 H301-LASER-INTERLOCK-LID

Insertion of the Sample Feedback Temperature Sensor

Insert the Sample Feedback Temperature Sensor through the dedicated opening located in the H301-PI-736-160x110

(see Figure 8, Front and 3D views).

Содержание H301-PI-736-160x110


















Результаты поиска

Содержание H301-PI-736-160x110

Отзывы:

Похожие инструкции для H301-PI-736-160x110

Бренды по названию

Популярные бренды

Okolab H301-PI-736-160x110, Руководство пользователя

Результаты поиска

Содержание H301-PI-736-160x110

Отзывы:

Похожие инструкции для H301-PI-736-160x110

Бренды по названию

Популярные бренды