manualshive.com logo in svg

Oki ML63326, Руководство пользователя, Страница: 65 / 322

Поделиться
Скачать
Oki ML63326 Скачать руководство пользователя страница 65

4-6

ML63326 User's Manual
Chapter 4  Interrupt (INT326)

(3) Interrupt request registers (IRQ0 to IRQ4)

IRQ0, IRQ1, IRQ2, IRQ3 and IRQ4 are registers that consist of 4 bits each.

When an interrupt request is generated, the corresponding bit of the interrupt request register
is set to "1" in the first half of the S1 state of the next instruction. So that the CPU can receive
interrupt requests, set the master interrupt enable flag (MIE) to "1" and set the appropriate
flag of the corresponding interrupt enable register (IE0 to IE4) to "1".

The watchdog timer interrupt is non-maskable and does not depend upon the interrupt enable
register or the master interrupt enable register (MIEF).

Setting the appropriate bits of an interrupt request register to "1" allows software interrupts
to be generated.

When an interrupt request is received, the corresponding bits of IRQ0 to IRQ4 are cleared
to "0".

At system reset, each bit of IRQ0 through IRQ4 is initialized to "0".

bit 3: QVI (reQuest Voice synthesis Interrupt)

This is the interrupt request signal from the voice synthesis section.

An interrupt request is generated when the setting of one voice phrase is
completed and the setting of the next voice phrase is enabled by the voice
synthesis section.

bit 2: QXI0 (reQuest eXternal Interrupt 0)

The external interrupt 0 request flag.

The external interrupt 0 is assigned as the secondary function of each bit of port
B (PB.0 to PB.3). External interrupt 0 requests are generated by a 4-bit ORed
input.

QVI

QXI0

QMD

QWDT

bit 3

bit 2

bit 1

bit 0

External interrupt 0 request flag
0: No request (initial value)
1: Request
Melody end interrupt request flag
0: No request (initial value)
1: Request

Watchdog timer interrupt request flag
0: No request (initial value)
1: Request

IRQ0 (055H)

(R/W)

Voice synthesis interrupt request flag
0: No request (initial value)
1: Request

Содержание ML63326



































































































































































































































































































































Отзывы:

Нет отзывов