Oki MB770 страница 24 Скачать руководство пользователя

Страница: 24 / 104

45372301TH Rev.2

3-8 /

Oki Data CONFIDENTIAL

[E] Stacker tray section

Fig. 3-8

Paper that is aligned in the finishing tray section is discharged to the stacker tray by the rotating ejector

belt which is driven by the ejector motor (M7). When paper is discharged from the processing tray, the

stacker tray is raised by the stacker motor (M8).

The SCU paddle tamps the trailing edge of the paper being discharged to the tray.

[E-1] Paper full alarm

The stacker tray lower limit detector switch (SW1) sends an alarm when it detects that the paper is

"Full" when the stacker tray is almost full of paper. (Approximately 50 sheets of paper can be added

after the alarm is sent.) The alarm is cancelled when paper is removed from the stacker tray.

[1] Ejector belt
[2] SCU paddle

[1]

[2]

Содержание MB770









































































































Результаты поиска

Содержание MB770

Отзывы:

Похожие инструкции для MB770

Бренды по названию

Популярные бренды

Oki MB770, Руководство по обслуживанию

Результаты поиска

Содержание MB770

Отзывы:

Похожие инструкции для MB770

Бренды по названию

Популярные бренды