Oki C9500dxn Скачать руководство пользователя

Страница: 132 / 220

41956001TH Rev.1

132 /

Oki Data CONFIDENTIAL

Table 6-1-1 Operator Alarms (3/6)

Message

Cause

Error Description

Solutions

Service Call
105: Error

Service Call
106: Error

Service Call
107: Error

Service Call
110: Error
~
116: Error

Service Call
120: Error

Service Call
121: Error

Service Call
122: Error

Service Call
123: Error

Service Call
124: Error

Service Call
125: Error

Turn power
OFF and wait
126: Dew
error

Service Call
127: Error

Service Call
130: Error

Service Call
131: Y Head
132: M Head
133: C Head
134: K Head

Service Call
140: Y ID
141: M ID
142: C ID
143: K ID

EEPROM not detected
at power ON.

Error in engine control
logic detected at power
ON.

Engine ROM
check sum error.

Option unit for different
model detected.
110: EnvelopeFeeder
111: Duplex unit
112: 2nd Tray
113: 3rd Tray
114: 4th Tray
115: 5th Tray
116: Finisher

PU unit fan motor error.

High-voltage power
supply I/F error.

Low-voltage power
supply fan error.
Low-voltage power
supply temperature error.

Improper environment
humidity detected by
sensor.

Improper environment
temperature detected
by sensor.

Error detected at MT
home position.

Sensor dew error.

Error detected at the

fuser unit cooling fan.

Temperature rise
detected at LED head.

Same unit not detected
upon power ON or
opening cover.

Error detected at
proper ID position.

Does EEPROM exist?
Does error reoccur?

Does error reoccur?

Does error reoccur?
Is error recovered by reloading PU F/W?

Is a proper option unit for the printer set?

1) Is fan in PU unit operating?

2) Error reoccurs after replacing fan motor.

Is cable between PU board andhigh-
voltage power LSI connected properly?

1) Is fan in low-voltage power supply unit
operating?
2) Error reoccurs after replacing fan motor.

1) Is error message displayed?
2) Does error reoccur?

Sensor dew error detected.

1) Does the fuser unit cooling fan operate?

2) Does the error repeat after fuser unit
cooling fan replacement?

1) Is error message displayed?

2) Does error reoccur?

1) Is error message displayed?
2) Is LED head properly set?
3) Does error reoccur?

1) Is error message displayed?
2) Does error reoccur?

Yes

Yes
Yes

Yes

Yes
Yes

Yes
Yes
Yes

Yes

Yes
Yes

Check for EEPROM and set if not
found.
Replace engine control board (K7N).

Replace engine control board (K7N).

Reload PU I/F.
Replace engine control board (K7N).

Set proper option unit.
Check connections and turn power
ON. If error is not recovered, replace
the unit.

Replace fan motor.
Replace engine control board (K7N).
Replace engine control board (K7N).

Connect properly.
Replace high-voltage power supply.
Check improper connections for
high-voltage.

Replace fan motor.
Replace low-voltage power supply.
Replace low-voltage power supply.

Turn ON power again.
Replace humidity sensor.

Turn ON power again.
Replace MT.

Turn ON power after a while.

Replace the fuser unit cooling fan.
Replace the engine control PWB (K7N).
Replace the engine control PWB (K7N).

Leave alone for 30 min.
Turn power OFF. Leave for 30 min.,
then turn power ON. Replace LED
head.

Confirm that LED head is set properly.
Turn power ON again.
Replace LED head assembly.

Turn power ON again.
Replace drum contacct assembly.

Содержание C9500dxn





























































































































































































































Результаты поиска

Содержание C9500dxn

Отзывы:

Похожие инструкции для C9500dxn

Бренды по названию

Популярные бренды

Oki C9500dxn, Руководство по обслуживанию

Результаты поиска

Содержание C9500dxn

Отзывы:

Похожие инструкции для C9500dxn

Бренды по названию

Популярные бренды