Oki C9500dxn Скачать руководство пользователя

Страница: 148 / 220

41956001TH Rev.1

148 /

Oki Data CONFIDENTIAL

An image is generally faint or the color is irregular. (Fig 6-2 A )

•

Is the amount of toner low? (Is [Toner Low] indicated?)

Yes

Refill toner.

▼

•

Is regulated paper used?

Use regulated paper.

▼

•

Yes

Is the LED head lens dirty?

Yes Clean the LED head lens.

▼

•

Are all items of the LED head assembly connected properly to the connection board (Y73
PWB) and engine board (K7N PWB)?

Check the cable connection (between each LED head and engine board), then connect the
cables between the LED head and engine board properly.

▼

•

Yes

Is +5V output to the following power connector pins on the connection board (Y73 PWB)?
+5V: Pin 1, 2, 3, 4, 5, 6

•

Yes Is +5V output to the each LED head assemblies on the connection board (Y73 PWB)?

3 pin for YPOW connector : LED head assembly - yellow
3 pin for MPOW connector : LED head assembly - magenta
3 pin for CPOW connector : LED head assembly - cyan
3 pin for KPOW connector : LED head assembly - black

Replace the connection board (Y73 PWB).

▼

•

Yes Check the cable connections, then replace the LED head assembly.

▼

•

Check the cable connections, then replace the low-voltage power unit. Did the printer
recover?

Yes End.

▼

•

Is 34V output to the power connector on the engine board (K7N PWB)?
+34V: Pin 12, 13, 14

Check the cable connections, then replace the low-voltage power unit.

▼

•

Yes

Is 34V output to the HVOLT connector pin 2 on the engine board (K7N PWB)?

Replace the engine board.

▼

•

Yes

Check the cable connections, then replace the high-voltage power unit or belt cassette
assembly.

Yes End.

▼

•

Is the I/D unit terminal connected properly to the contact assembly. (See Fig. 6-2)

Connect the I/D unit terminal properly to the contact assembly.

▼

•

Yes

Replace the image drum.

Note: 1. Remove EEPROM from the old board and set it on the new board upon replacing the

engine board (K7N PWB).

2. If EEPROM is not replaced, refer to section 4.2.2.

Содержание C9500dxn





























































































































































































































Результаты поиска

Содержание C9500dxn

Отзывы:

Похожие инструкции для C9500dxn

Бренды по названию

Популярные бренды

Oki C9500dxn, Руководство по обслуживанию

Результаты поиска

Содержание C9500dxn

Отзывы:

Похожие инструкции для C9500dxn

Бренды по названию

Популярные бренды