Oki B6500 Series Скачать руководство пользователя

Страница: 111 / 162

1 – 107

Chapter 1 Troubleshooting

FIP4.9 SENSOR LOW PAPER

Step Check

Yes

Possible causes:

SENSOR LOW PAPER (PL20.1.30)

ACTUATOR LOW PAPER (PL20.1.31)

HARNESS LOW PAPER (PL20.1.33)

HARNESS ASSY FDR2 (PL20.1.5)

Option 550 Paper Feeder 550 PAPER CASSETTE

PWBA FEEDER 550 (PL20.1.34)

PLATE ASSY BTM (PL20.3.10)

HVPS/MCU (PL12.1.19)

Checking ACTUATOR LOW PAPER

Remove Option 550 Paper Feeder. (RRP20.1)

Install 550 PAPER CASSETTE.

Move PLATE ASSY BTM up and down.

Does ACTUATOR LOW PAPER operate smoothly?

Does the flag go into the detecting area of the sensor

when PLATE ASSY BTM is up state (ACTUATOR LOW

PAPER is pushed up), and out of the detecting area

when PLATE ASSY BTM is pressed down?

With tool Go to

step 2. Without

tool Go to step 3.

Replace ACTUA-

TOR LOW PAPER.

Checking SENSOR LOW PAPER (1)

Install Option 550 Paper Feeder. (RRP20.1)

Remove EP CARTRIDGE.

Close COVER OPEN (PL1.1.2).

Remove 550 PAPER CASSETTE.

Put the hand in the cassette insertion space, move

ACTUATOR LOW PAPER.

Does the number increase one by one, as ACTUATOR

LOW PAPER operate?

Check using Chapter 2 Diagnostic [Sensor/Switch

Check].

Replace HVPS/

MCU.

(RRP12.10)

Go to step 3.

Checking SENSOR LOW PAPER (2)

Install Option 550 Paper Feeder. (RRP20.1)

Remove EP CARTRIDGE.

Close COVER OPEN (PL1.1.2).

Remove 550 PAPER CASSETTE.

Put the hand in the cassette insertion space, move

ACTUATOR LOW PAPER.

Is the voltage across P/J81-3(+) and P/J81-2(-), 3.3

VDC when ACTUATOR LOW PAPER is held up, and 0

VDC when released?

Go to FIP4.6, 4.7

PWBA FEEDER

550.

Go to step 4.

Checking HARNESS LOW PAPER for continuity

Install Option 550 Paper Feeder. (RRP7.1)

Disconnect the connector of SENSOR LOW PAPER.

Disconnect P/J81 from PWBA FEEDER 550.

Is there continuity between J81 and J810?

Go to step 5.

Replace HAR-

NESS LOW

PAPER.

Checking HVPS/MCU for continuity

Disconnect P/J11 and P/J20 from HVPS/MCU.

Is there continuity between P11-16 and P20-5?

Go to step 6.

Replace HVPS/

MCU. (RRP12.10)

Checking SENSOR LOW PAPER (3)

Replace SENSOR LOW PAPER. (RRP20. 7)

Does the problem still occur, after replacement?

Replace HVPS/

MCU.

(RRP12.10)

End of work

Содержание B6500 Series



































































































































































Результаты поиска

Содержание B6500 Series

Отзывы:

Похожие инструкции для B6500 Series

Бренды по названию

Популярные бренды

Oki B6500 Series, Руководство по устранению неисправностей

Результаты поиска

Содержание B6500 Series

Отзывы:

Похожие инструкции для B6500 Series

Бренды по названию

Популярные бренды