English
7
Material Safety Data
Sheet #58367401
52114501 Print Cartridge Toner
52114502 Print Cartridge Toner
For more information, contact Oki Data at 2000 Bishops
Gate Blvd., Mount Laurel, NJ, 08054-4620.
Emergency Information: call 1-800-654-3282; US & Canada
Only.
Emergency First Aid ____________
Toner swallowed (ingested).
Rinse out mouth with water and give several glasses of water
to drink. Seek medical attention.
Toner inhaled.
Remove person to fresh air. Rinse mouth with water.
Toner gets in the eyes.
Flush eyes with large quantities of cool water for 15 minutes,
keeping the eyelids open with fingers. Seek medical
attention.
Toner gets on the skin.
Wash toner off the skin with plenty of cool water and soap.
Note:
Small amounts of toner on skin or clothing can easily
be removed with soap and
cold
water. Hot water
makes toner harder to remove.
Hazardous Ingredients__________
Polyester (40-50% by weight)
CAS#: Not available
OSHA PEL: Not available.
Magnetite (40-50% by weight)
CAS#: 1309-38-2
OSHA PEL: Not available.
Propylene Wax (1-5% by weight)
CAS#: Not available
OSHA PEL: Not available.
Ethylene/Propylene Resin (1-5% by weight)
CAS#: Not available
OSHA PEL: Not available.
Amorphous Silica (1-5% by weight)
CAS#: 7631-86-9
OSHA PEL: Not available.
Physical Data __________________
Physical State:
Solid
Melting/Freezing Point:
Not available
Boiling Point:
Not applicable
pH:
Not available.
Vapor Pressure:
Not applicable
Vapor Density (Air=1):
Not available
Evaporation Rate (Butyl Acetate=1)
: Not available
Specific Gravity (H
2
O=1):
Not available
Solubility in Water:
Negligible
Solubility in Solvents:
Not available
Coefficient of Water/Oil Distribution:
Not available
Appearance and Odor:
Black powder, faint odor
Odor Threshold:
Not available
Fire and Explosion Hazard Data _
Flash Point (O°C):
Not applicable.
Flammability:
Not flammable under conditions of use.
Flammable Limits
Lower Explosive Limit
: Not applicable
Upper Explosive Limit:
Not applicable
Auto-ignition Temperature:
Not applicable
Explosion Data
Like most organic materials in powder form, the toner can
form explosive mixtures when dispersed in air.
Sensitivity to Mechanical Impact:
Not available
Sensitivity to Static Discharge:
Not available.
Extinguishing Media:
Water spray, foam, dry chemicals.
Special Fire Fighting Procedures:
In case of fire, use
extinguishing media. When mounted in the printer, treat as an
electrical fire.
Hazardous Combustion Products:
Not applicable
Toxicological Properties ________
Routes of Entry:
Inhalation, Ingestion, Eyes, Skin
Effects of Acute Exposure
(based on
toxicity data for similar
materials and ingredients
):
Swallowed LD
50
(rat):
> 5000 mg/kg
Skin LD
50
(rabbit):
> 5000 mg/kg
Inhaled LC
50
(rat):
> 5 mg/L/4hr
Effects of Chronic Exposure
(based on
toxicity data for
similar materials and ingredients)
:
The results obtained from a
sponsored, Chronic Toner Inhalation Study, demonstrated no
lung change in rats for the lowest (1 mg/m
3
) exposure level
(i.e. the level most relevant to potential human exposure).
A very slight degree of fibrosis was noted in 25% of the
animals at the middle (4 mg/m
3
) exposure level, while a slight
degree of fibrosis was noted in all the animals at the highest
(16 mg/m
3
) exposure level.
These findings are attributed to "lung overloading," a generic
response to excessive amounts of any dust retained in the
lungs for a prolonged period. This study was conducted using
a special test toner to comply with EPA testing protocol. The
test toner was ten times more respirable than commercially
