Okay FGS 80-1 LI, Руководство по эксплуатации

Страница: 36 / 40

GB | Operating Instruction
34
protection that protects the battery from damage. This
feature switches the battery off if the discharging thresh-
old is reached. Do not switch the tool on afterwards and
make sure to recharge the battery first.
Switching the tool on/off
(fig. 3)
Slide the switch-on lock (5) forward and push switch (6).
After the tool has been switched on, you do not have to
hold the switch-on lock (5) any longer.
To switch off just let go of the switch (6).
Attention! The blades will coast for a certain
time after switch-off!
Hints for your work with the tool
As the device is operated with one hand
please be careful not to move the other hand
near the running cutting tools.
Maintenance
(Fig. 4 - 6)
When performing the following tasks to
change the shear system, do not, under any
circumstances, switch on the device! Danger
of injury!
Put the included blade guard into the blade(s) and use
protective gloves to protect yourself from injury.
Push both lateral push buttons concurrently and remove
the shearing blades (Fig. 4).
Remove any dirt from the gear area (if necessary).
Please slightly grease the drive area (C) using commer-
cial universal grease as described in the Maintenance
section before putting the replacement shears in place
(Fig.6).
Lead the cutting blades with the rear holding toe into
the housing of the grass shears as shown in fig. 5 and
lock the click system in place by strongly pushing on the
blade base plate.
The position of the eccentric drive does not have to be
considered when changing the blades. When the device
is switched on, the gear eccentric unit automatically
engages into the appropriate relief in the shearing blade.
The device is now ready for operation.
Clean the blade from any crushed plants and dirt. The
blades should be detached at least once a season for
the removal of debris. Lubricate the (C) pinion and the
(D) back of the blade with a light oil. Do not lubricate the
motor and other parts. Should the blade become dull
after a long period of use, a spare part can be ordered.
Warning! The leading edges of the blades must be oiled
to ensure proper lubrication. If the leading edges are not
oiled, blade durability may be adversely affected.
If the cutting tools have become dull after long use
please replace them with original spare parts.
Clean the device using only a brush or cloth. Do never
wash down the device with water and do never dip the
device into water.
Apply protective spray to the blades after each use.
Replace blunt blades.
Always put on the blade guard after use.
Examine the tool for obvious defects and have it re-
paired in an authorised service shop if required.
Storage
Always store the tool in a dry, clean place outside the
reach of children. Make sure that the place of storage
is frost-free.
Spare parts
If you need accessories or spare parts, please contact
our Service department.
When working with this tool, do not use any accessory
parts other than those recommended by our company.
Otherwise the operator or others in the vicinity could suffer
serious injuries, or the tool could be damaged.
Waste disposal and environmental protection
Please note the following instructions regard-
ing disposal:
Worn out electrical appliances and batteries do
not belong with your household waste.
Electrical appliances must be collected, recycled
or disposed of in an environmentally friendly
manner.
Defective or spent batteries must be recycled
properly in accordance with the latest regulations
concerning battery and accumulator disposal.
Before removing the installed accumulator with printed
board from your appliance, actuate the ON/OFF switch
and wait until the accumulator has fully discharged.
Then use a screwdriver to undo all screws on the appli-
ance and open the casing.
Remove the printed board with lithium ion cell and
disconnect the connections on the accumulator/printed
board.
Then hand in the printed board with lithium ion cell at an
accumulator/battery recycling point for proper disposal.
In line with the European Electrical and Electronic Equip-
ment Directive, after removing the printed board with
accumulator, you must deliver the appliance for environ-
mentally friendly recycling.
We would, however, also be happy to handle the proper
disposal of the appliance with accumulator on your
behalf. To take advantage of this offer, send the appli-
ance to the service address provided in the operating
instructions.