background image

10.

Grip the piston shaft with soft jaws 727-02. 
Fit the O-ring on the adjustment needle. 
Apply plenty of red grease on the O-ring so 
that the needle slides easily into the piston 
shaft.

11.

Check the X-ring and O-ring on the seal 
head. Replace if necessary. Smear plenty 
of white grease on the X-ring before you fit 
it. Use tool 0715-01 to get the X-ring into 
the right position.

10.

Wrap some teflon tape arond the thread 
of the shaft to protect the seal and O-ring 
from damages. Apply some red grease 
(146-01) to the tape and the shaft end. 
Mount the seal head and the O-ring.  

11.

Use a brass wire brush to clean the piston 
rod from tape. Mount Spacer, Sleeve, Top-
out spring and the Piston holder.

12.

Tighten the Piston holder to a torque of 15 
Nm.

13.

Refit the Compression/Rebound valve. Use 
the picture below to make it right. Tighten 
the 8 mm nut with a torque of 7 Nm.

10

11

10

11

12

13

X-ring

O-ring

Piston holder

Topout spring

Sleeve
Spacer

REBOUND 

LEG (RH)

COMPRESSION 

LEG (LH)

8 mm Nut (7 Nm)

NOTE!

CAUTION!

530-22, Shims

525-18, Shims

1149-01, W

ave

Shim Stack

(compr

ession) 

2061-03, Piston

Clamp (comp.)

1447-02, 

Piston ring

Shim stack

(r

ebound)

Clamp (r

ebound)

1675-01, Nut

1654-09, 

Piston holder

1674-01, W

asher

1654-09, 

Piston holder

Shim stack

(compr

ession)

1447-02,

Pison ring

2061-03, Piston

Shim stack

(r

ebound)

Clamp (r

ebound)

1674-01 2x,

W

a

sher

1675-01, Nut

Clamp (comp.)

CAUTION!

14

15 Nm

Tool 0715-01

525-18, Shims

1674-01, W

asher

Содержание FG 670





























Отзывы: