OfiTE 150-80 Скачать руководство пользователя страница 5

Страница: 5 / 29

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

Installation

1. Assemble the Cup Assemblies as illustrated below and in the drawing

on page 24. The brass weight is an optional piece for simulating an

overburden pressure applied to the swelling core sample.

2. Assemble the Main Assemblies as depicted below and in the drawing on

page 26. Adjust the height of the head assembly such that there is a

small gap (approximately 5 mm) between the bottom of the nut on the

spindle and the body of the LVDT without a wafer inserted into the cup

assembly.

Transfer Stand

(#150-80-032)

Cap for Wafer Tube

(#150-80-036)

Bottom (Main) Plate

(#150-80-034)

Teflon Washer

(#150-80-031)

Brass Weight (Optional)

(#150-80-009)

Wafer Tube

(#150-80-033)

Magnetic Stir Bar

(Comes w/Hot Plate)

(#153-53-1)

Cup

(#150-80-035)

Micrometer (#150-80-067)

LVDT (#150-80-064)

Nut (#150-80-093)
Head (#150-80-013)

Cup Assembly (see above)

Stirring Hot Plate

(#150-83)

Locking Nut (#150-80-001)

Содержание 150-80






























Результаты поиска

Содержание 150-80

Отзывы:

Похожие инструкции для 150-80

Бренды по названию

Популярные бренды

OfiTE 150-80, Инструкция по эксплуатации

Результаты поиска

Содержание 150-80

Отзывы:

Похожие инструкции для 150-80

Бренды по названию

Популярные бренды