manualshive.com logo in svg

OfiTE 120-05, Инструкция по эксплуатации, Страница: 37 / 41

Поделиться
Скачать
OfiTE 120-05 Скачать руководство пользователя страница 37

OFITE, 11302 Steeplecrest Dr., Houston, TX 77065 USA / Tel: 832-320-7300 / Fax: 713-880-9886 / www.ofite.com

36

During a test, the computer will be continuously adjusting the pressure inside 

the cell. As the pressure increases due to thermal expansion, the computer 

will allow pressure to bleed. Likewise, if pressure begins to drop, the 

computer will add pressure to keep it within the target range.

There is a secondary 

Regulator

 (#120-50-037) which controls the air 

pressure to the pressure relief valve.

This regulator comes calibrated and requires no adjustment unless a part 

within this system has been replaced.

If the user must gain access to the regulator, simply remove the back panel 

of the instrument. The regulator and gauge are located inside.  There is one 

set on each side. To set the regulator to the proper pressure, apply pressure 

to the system and begin opening the regulator between 50 - 80 psi (344.7 - 

551.6 kPa). If the pressure relief valve does not open, continue adjusting the 

regulator to a higher pressure as needed to obtain optimal operation of the 

relief valve.

Maintenance

Pressure Relief Valve 

Regulator

Air Regulator

(#120-50-037)

Gauge

(#143-01)

Содержание 120-05










































Отзывы:

Нет отзывов