OEM VKP80III Скачать руководство пользователя страница 41

Страница: 41 / 96

5.4 Printer

parameters

This printer allows the con

guration of the parameters listed in the following table.

The parameters marked with the symbol

are the default values.

Settings remain active even after the printer has been turned off and they are stored in non-volatile memory.

PRINTER

EMULATION

Available emulations for the device:

VKP80III

VKP80II

RS232 BAUD RATE

Communication speed of the serial interface:

115200

19200

2400

57600 9600 1200
38400

4800

NOTE:

Parameter valid only with serial interface.

RS232 DATA LENGTH

Number of bit used for characters encoding:

7 bits/car
8 bits/car

NOTE:

Parameter valid only with serial interface.

RS232

PARITY

Bit for the parity control of the serial interface:

None

= parity bit omitted

Even =

even value for parity bit

Odd =

odd value for parity bit

NOTE:

Parameter valid only with serial interface.

RS232

HANDSHAKING

Handshaking:

XON/XOFF = software handshaking
Hardware

= hardware handshaking (CTS/RTS)

NOTE:

Parameter valid only with serial interface.

NOTE:

When the receive buffer is full, if handshaking is set to XON/XOFF, the printer sends the XOFF

($13) on the serial port. When the receive buffer has cleared once again, if handshaking is set to XON/
XOFF, the printer sends the XON ($11) on the serial port.

BUSY

CONDITION

Activation mode for Busy signal:

OffLine/ RXFull = Busy signal is activated when the printer is both in OffLine status

and the buffer is full

RXFull

Busy signal is activated when the buffer is full

NOTE:

Parameter valid only with serial interface.

USB MASS STORAGE

Sharing mode from Mass Storage:

Disabled

= sharing mode disabled

Enabled =

sharing mode enabled

NOTE:

The parameter is printed only with VKP80III emulation enabled

USB

ADDRESS

NUMBER

Numerical address code for the univocal identifi cation of the USB device (in case of
more than a USB device connected with the same PC):

2 4

6 8

1 3 5 7 9

5. CONFIGURATION

User Manual

VKP80III 41

Содержание VKP80III

































































































Результаты поиска

Содержание VKP80III

Отзывы:

OEM VKP80III, Руководство пользователя, Страница: 41 / 96

Результаты поиска

Содержание VKP80III

Отзывы: