manualshive.com logo in svg

OEM BL2500, Руководство пользователя, Страница: 54 / 71

Поделиться
Скачать
OEM BL2500 Скачать руководство пользователя страница 54

EMBEDDED

 PLC BL2500 User’s Manual 

 

Loading or Upgrading the Firmware Kernel 

OEM Technology Solutions 

 

Page 48 

6.  LOADING OR UPGRADING THE FIRMWARE KERNEL 

6.1 INTRODUCTION 

The 

EMBEDDED

 PLC Utility is used to load the 

EMBEDDED

 PLC Firmware Kernel to the Rabbit-based Target 

such as the SBC BL2500. The Firmware Kernel, once loaded into the Target, requires a license key to 
run.  The 

EMBEDDED

 PLC Utility does not check for an existing license key before loading the Kernel. 

Thus, a new license key is required after a Kernel is loaded to a Target. 

Upgrading the EMBEDDED PLC Firmware Kernel means also loading the newer version of the Firmware 
kernel file into the Target. Therefore after loading a newer version of the Firmware Kernel file into a 
licensed Target PLC, a new license key will also be required. 

,

 

Caution:

 

 

Loading of the Firmware Kernel file is 

NOT

 needed if you purchased the 

EMBEDDED

 PLC 

Application Kit as the BL2500 comes with a pre-loaded and licensed Firmware Kernel. If you re-
load the Firmware Kernel to a pre-loaded Target, the license information will be lost and a new 
license key will be required. 
To verify if your BL2500 have the 

EMBEDDED

PLC Kernel running, power up the BL2500 and if 

after 10 seconds the DS2 red LED turns off and DS1 starts flashing then the Kernel is loaded 
and licensed. 

This chapter describes how to install the 

EMBEDDED

 PLC Utility, load and license the 

EMBEDDED

 PLC 

Firmware Kernel. Also includes a complete reference of the Utility software. 

6.1.1 Installing 

EMBEDDED

 PLC Utility 

Use the following procedure to install 

EMBEDDED

 PLC Utility from the CD-ROM: 

1. Insert 

the 

EMBEDDED

 PLC BL2500 CD-ROM and open the root folder. 

2. Double-click 

on 

the 

EmbeddedPLCUtility_V1.03_3-0237G.msi

 file to launch the 

EMBEDDED

 

PLC Utility Setup Wizard. Follow the on screen instructions to proceed with the installation. 

3.  Once all the 

EMBEDDED

 PLC Utility files have been copied, the 

EMBEDDED

 PLC Utility icon is added to 

your Desktop and the following group is added to your main Programs group: 

 

6.1.2  Connecting to the BL2500 

1.  Connect the 10-pin 

PROG

 connector of the programming cable to header J3 on the BL2500’s 

RabbitCore module. Ensure that the coloured edge lines up with pin 1 as shown in Figure 12. There 
is a small dot on the circuit board next to pin 1 of header J3. (Do not use the 

DIAG

 connector, which 

is used for licensing and configuring only). Connect the other end of the programming cable to a COM 
port on your PC. Make a note of the port to which you connect the cable, as the 

EMBEDDED

 PLC Utility 

will need to have this parameter configured. Note that COM1 on the PC is the default COM port used 
by the 

EMBEDDED

 PLC Utility. 

Содержание BL2500








































































Отзывы:

Нет отзывов