Octave V 80 SE Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 48

background image

29

7. ADVANCED FUNCTIONS

The V 80 SE incorporates a separate solid-state headphone amplifier. The headphone output is via
a 6.3 mm stereo jack and is suitable for high impedance headphones between 30 and 2000 ohms.
If you have headphones with an impedance between 4 and 30 ohms, you should either use a
separate headphone amp or connect them to the speaker outputs via an adapter.
The 3 positions of the headphone switch [10

]

offer the following options:

-

Position A is for speakers only and the headphone amplifier is switched off.

- In position B (centre position) both speaker and headphone outputs are available. The

Headphone LED [7] on the front panel will now illuminate

-

In position C, Ecomode switches the tube section of the V 80 SE off. The power amplifier is
powered down immediately, without any delay. The Headphone, Ecomode and Soft-start LEDs
now light up. The tube section is permanently switched off and Ecomode will not respond to
the presence of a signal.

Note 1
If you try to use the on/off switch to switch the amplifier on while the headphone switch is in
position C, the tube power amplifier section will not power up. You have to move the switch to
position A or B to start the tube power amplifier up and listen to your loudspeakers.

Note 2
If you try to use the on/off switch to switch the V 80 SE on when the headphone switch in position
C (headphones only) and the Ecomode switch in position B (Ecomode ON), the tube power
amplifier section will not power up.

If you wish to listen to your speakers you must change the position of the headphone switch. When
the Ecomode switch is in the Ecomode ON position, the tube section can only be activated and
powered up by a signal from a source component. (The "Automatic power up with Ecomode ON"
function is disabled in position C (headphones only)).

Note 3
As the tube circuitry is deactivated/activated as soon as you turn the headphone switch [10] to or
from position C, you should wait at least 40 seconds before doing so if the amplifier has already
reached operating temperature. Accidentally switching the headphone switch to C and back to A
just once is not detrimental to the amplifier or the output tubes. However, doing this more than 5
times in 10 minutes would result in a substantial rise in the temperature of the soft-start/surge
attenuator components.
We have therefore located the switch on the rear panel to keep it away from curious, small hands.

«
...
26
27
28
29
30
...
»

Содержание V 80 SE

















































Отзывы:

Нет отзывов

Похожие инструкции для V 80 SE

Бренд: Parasound Страницы: 16

Бренд: B&K Страницы: 16

Бренд: Velleman Страницы: 29

Бренд: D.W. Fearn Страницы: 21

Бренд: ESX Страницы: 20

UP 4000 Series UP4121

Бренд: Mackie Страницы: 4

Steve Morse Signature 100

Бренд: Engl Страницы: 37

909 Stereo Power Amplifier

Бренд: QUAD Страницы: 14

Бренд: Imagine Страницы: 52

Бренд: Lyngdorf Audio Страницы: 20

Бренд: Chord Страницы: 35

Бренд: Evolution Amps Страницы: 28

Бренд: Crown Страницы: 2

Redeye 3D Phantom

Бренд: Little Labs Страницы: 6

Бренд: Gallien-Krueger Страницы: 8

Бренд: Fender Страницы: 3

Бренд: CTR Страницы: 25

Preference Mic Pre 2711

Бренд: Sound Performance Lab Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды