manualshive.com logo in svg
background image

 

 

 

2. SAFETY PRECAUTIONS 

 

 

2.1 BEFORE YOU BEGIN 

 

Read the instructions before switching 
the unit on.   

Please read through this manual carefully 
before switching on your amplifier and pay 
particular attention to the safety instructions. 
Please keep this manual safe for future ref-
erence and retain the original packing to use 
whenever your amplifier is transported. 
 

In case of emergency: disconnect the 
plug from the mains supply  

Never use an amplifier that is damaged or 
faulty. Make sure that it cannot be used until 
it has been repaired by a qualified service 
engineer. You should also remove the mains 
plug if you expect not to use the amplifier for 
a long period.  
 

Do not open the case  

There are dangerously high voltages and hot 
tubes inside this equipment. To avoid a burn 
or the risk of electric shock, never allow 
anyone except qualified personnel to open 
the case.  
 

Servicing and maintenance  

To avoid the risk of any other hazards, ser-
vicing, repairs and other modifications to this 
OCTAVE equipment should only be carried 
out by qualified personnel. Always replace 
fuses with ones of the same type and rating. 
If your amplifier requires servicing, please 
ship or take your equipment directly to OC-
TAVE or to one of our authorized service 
centres.  
 

Explanation of the symbols  

 

 

The lightning flash with arrowhead symbol 
within an equilateral triangle is intended to 
alert the user to the presence of uninsulated 
'dangerous voltages' within the product's 
enclosure that may be sufficient to constitute 
a risk of electric shock to persons. 
 
The exclamation point within an equilateral 
triangle is intended to alert the user to im-

 

 
 
portant operating and maintenance instruc-
tions.  
The CE mark certifies that this electrical 
equipment complies with current European 
Union product safety regulations such as 
the Low Voltage Directive and the Electro-
magnetic Compatibility Directive. 
 

Before connecting up  

The Jubilee preamplifier is designed to 
operate exclusively with the power supply 
supplied. Make sure before connecting the 
power cord that your amplifier is suitable 
for your local supply voltage.  
 

Protection class  

In Japan this amplifier is a protection class 
2, no earth connector. In other countries it 
is a protection class 1 device (with protec-
tive earth conductor).  
 

Adjusting the volume  

While you are setting your amplifier up, 
turn the volume control anticlockwise, close 
to the minimum setting. High sound pres-
sure levels can damage to your hearing as 
well as your loudspeakers.  
 

Safety warning: Hot tubes  

Tube equipment gets very hot and takes 
about 20 minutes to cool down after you 
have switched it off. The exterior of the 
case, which can also heat up during normal 
operation, and the protective grill fitted over 
the external tubes are designed to protect 
children and others from being burned 
should they ever touch the hot tubes. 
Warning: Remove the protective grill at 
your own risk. OCTAVE accepts no re-
sponsibility for injuries caused by the re-
moval of this grill.  
 

Warranty  

OCTAVE can only guarantee the safety, 
reliability and performance of this unit if 
modifications and repairs are carried out by 
specialized personnel and if the amplifier is 
operated in accordance with the instruc-
tions contained in this manual.

 

 

Содержание JUBILEE Pre























Отзывы: