Oce CS4236 Скачать руководство пользователя страница 68

Страница: 68 / 102

Description

Scanner mode

Scanner not accessible. Océ Scanner Agent has not (yet) detected
the scanner.

"<N/A>"

The connected scanner is not a model compatible with Océ
Scanner Agent.

"Scanner is unsup-
ported"

This message is displayed while downloading firmware to the
scanner.

"Scanner is busy or
turned off"

The scanner is in this mode when firmware is being downloaded
with the firmware.exe program.

"Programming
Mode. Firmware
may be download-
ed"

The scanner is initializing its settings (start-up).

"Initializing"

The scanner needs to warm up before it can function in optimal
conditions. This takes a few minutes.

"Warming Up"

The scanner is ready for scanning.

"Ready"

An error was detected. View the error message.

"Not Ready. Error
detected"

The scanner test mode is used during technical service.

"Test Mode"

The scanner is performing test operations to ensure optimal
performance: light profile corrections, stitching, etc.

"Continuous self-
test mode"

The scanner is performing calibration of the cameras.

"Calibrating"

The scanner is adjusting its cameras.

"Adjusting"

The scanner is in standby mode when the LED indicator is red.
The Timer powers the scanner on and off from the standby
mode.

"Standby"

Error messages

This field relays errors returned from the scanner and related to the current Scanner mode.
When there is no error detected in the Scanner mode field, <None> is displayed in the
Error messages.

Error messages are useful for troubleshooting your scanner’s function or connection. Here
is a list of error messages:

Chapter 8 - Océ Scanner Agent

Interface of Océ Scanner Agent

Содержание CS4236







































































































Результаты поиска

Содержание CS4236

Отзывы:

Похожие инструкции для CS4236

Бренды по названию

Популярные бренды

Oce CS4236, Руководство пользователя

Результаты поиска

Содержание CS4236

Отзывы:

Похожие инструкции для CS4236

Бренды по названию

Популярные бренды