Observator Instruments OMC-042 Скачать руководство пользователя страница 103

Страница: 103 / 106

OMC-042 / 043 / 044 Data loggers

Users

’ manual

page 103

System messages

Meaning of the System messages (S-records in TXT and CSV or $Msg-lines in JSON data log files)

A System message contains a message code, an optional supplemental code/text and an optional
explanatory text.

Please find below a list with possible System messages.

Message code

Supplemental code/text

Meaning

Possible cause/reason

SYS_START

"System name & S/N"

System is started and deployed

At power on, or reset

SYS_DEPLOYED

"System name & S/N"

System is deployed

After a delayed deployment

SYS_UPGRADED

"System name & S/N"

Firmware upgrade detected

After firmware upgrade

CFG_CHANGED

"System name & S/N"

Configuration has changed

After configuration editing

CFG_ERR

Configuration error

Firmware downgrading, or configuration
upload with different version

NO_CFG

No configuration detected

Data logger is not yet configured

CFG_UPL

"cause of failure"

Configuration upload failed

Disruption in the data transfer, or SD
card failure

FW_UPG

"cause of failure"

Firmware upgrade failed

Disruption in the data transfer, or SD
card failure

PVD_DIP

"number"

Power voltage detection dips

When the internal power (temporarily)
drops unexpectedly below 2.8V (power
has returned before switch off occurred)

SD_FAIL

"number"

Number of temporarily SD card
failures

SD card failure

NETWORK

"fallback;2G"

Network fallback (only for
2G+3G Modems)

When 3G network is not available

WDT

"Sensor name"

Shows the sensor driver name
were the watchdog timeout
occurred

Sensor defect, or wrongly connected, or
warmup time too short

WDT

MODEM_INIT

Watchdog timeout while
initializing Modem

No response from Modem, or no SIM, or
SIM not detected, or PIN on SIM

WDT

NETWORK_REG

Watchdog timeout while trying to
register on a network

No response, or (temporarily) no network
coverage, or SIM subscription failure
(inactive/invalid/blocked or black listed)

WDT

APN_OPEN

Watchdog timeout while trying to
find an internet access point

No response, or APN access point name
wrong

WDT

APN_LOGIN

Watchdog timeout while trying to
login to the internet access point

No response, or APN user or password
wrong, or authentication failure

WDT

SERVER_LOGIN

Watchdog timeout while trying to
login to the
Email/FTP/TCP/HTTP server

No response, or server not available, or
credentials wrong

WDT

FILE_OPEN

Watchdog timeout while trying to
open a file on the FTP server

No response, or file handling error on the
server

WDT

DATA_SENDING

Watchdog timeout while sending
data to the
Email/FTP/TCP/HTTP server

No response, or unexpected network
disruption, or server error

WDT

TCP_RESPONCE

Watchdog timeout while waiting
for acknowledge from the
TCP/HTTP server

No response, or unexpected network
disruption, or server error

WDT

DATA_END

Watchdog timeout while trying to
disconnect from the
Email/FTP/TCP/HTTP server
connection

No response, or unexpected network
disruption, or server error

WDT

"STATE number"

Modem state machine step
where the watchdog timeout
occurred

No response

ERR

"Driver name"

Shows the driver name were an
error occurred, with if applicable
some additional information

Sensor defect, or unknown failure

ERR

MODEM_INIT

Error while initializing Modem

No SIM, or SIM not detected, or PIN on
SIM

ERR

NETWORK_REG

Error while trying to register on a
network

(Temporarily) no network coverage, or
SIM subscription failure
(inactive/invalid/blocked or black listed)

Содержание OMC-042











































































































Результаты поиска

Содержание OMC-042

Отзывы:

Похожие инструкции для OMC-042

Бренды по названию

Популярные бренды

Observator Instruments OMC-042, Руководство пользователя

Результаты поиска

Содержание OMC-042

Отзывы:

Похожие инструкции для OMC-042

Бренды по названию

Популярные бренды