background image

31

308–030

TECHNICAL DATA

Electric Motor

0.5 HP, 1725 rpm, 115V, 60HzAC, 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

single phase with automatic thermal overload switch. UL Listed

Electric Cord

No. 14 gauge, 3 wire

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maximum Working Pressure

2500 psi (172 bar)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Maximum Delivery

0.33 GPM (1.25 liter/min)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Cycles/Gallon (liter)

750 (197)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Tip Size

one gun to 0.017 tip 

with latex at 2000 psi (138 bar)

. . . . . . . . . . . . . . . . . . . 

Wetted Parts

Displacement Pump

Carbon Steel, Polyurethane, Polyethylene,

. . . . . . . . . . . . . . . 

Alloy Steel, Zinc–Plated Steel, Delrin

r

, Leather

Filter

Aluminum, Carbon Steel, Stainless Steel

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Fluid Inlet

3/4 npt(m) with 30

_

 ID chamfer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Fluid Outlet Size

1/4 npsm(m)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Dimensions

Weight

60 lb (27 Kg)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Height

17.5 in (444.5 mm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Length

25.5 in. (648 mm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

Width

14 in. (356 mm)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

NOTE: Delrin

r

 is a registered trademark of the DuPont Co.

IMPORTANT PHONE NUMBERS

TO PLACE AN ORDER, contact your Fuller O–Brien dis-
tributor, or  call this number to identify the distributor closest
to you: 1–800–328–0211  Toll Free

FOR TECHNICAL ASSIST

ANCE, service repair information

or assistance regarding the application of Fuller O–Brien
equipment:

1–800–543–0339 Toll  Free

Содержание PRO 301

































Отзывы: