background image

OWNER’S MANUAL

308–030

Rev A

PRO 301

 Airless Paint Sprayer

1/3 GPM, Electric

Model 223–636, Series A

2500 psi (172 bar) MAXIMUM WORKING PRESSURE

TABLE OF CONTENTS

Warnings

2

. . . . . . . . . . . . . . . . . . . . . 

Setup

8

. . . . . . . . . . . . . . . . . . . . . . . . 

Startup

10

. . . . . . . . . . . . . . . . . . . . . . 

Maintenance

11

. . . . . . . . . . . . . . . . . 

Application Techniques

12

. . . . . . . . 

Flushing Guidelines

13

. . . . . . . . . . . 

Troubleshooting Guide

14

. . . . . . . . 

Repair

15

. . . . . . . . . . . . . . . . . . . . . . 

Parts

24

. . . . . . . . . . . . . . . . . . . . . . . 

Accessories

28

. . . . . . . . . . . . . . . . . 

Technical Data

31

. . . . . . . . . . . . . . . 

Dimensions

31

. . . . . . . . . . . . . . . . . . 

Warranty

32

. . . . . . . . . . . . . . . . . . . . 

THE O’BRIEN CORPORATION, 450 E. Grand Avenue, So. San Francisco, CA 94080

COPYRIGHT 1990, GRACO INC.

This manual contains IMPORTANT
INSTRUCTIONS and WARNINGS.
READ AND RETAIN FOR REFERENCE.

Liquids can be injected into the body by high pressure  airless  spray
or  leaks – especially hose leaks.
Keep body clear of the nozzle. Never stop leaks with any part of the
body. Drain all pressure before removing parts.Avoid accidental trig-
gering of gun by always setting safety latch when not spraying.
Never spray without a tip guard.
In case of accidental skin injection, seek immediate
“Surgical Treatment”.
Failure to follow this warning can result in amputation or serious
injury.

FIRE AND

EXPLOSION HAZARD

SKIN INJECTION

HAZARD

READ AND UNDERSTAND ALL LABELS AND INSTRUCTION MANUALS BEFORE USE

Spray painting, flushing or cleaning equipment with flammable liq-
uids in confined areas can result in fire or explosion.

Use  outdoors or in extremely well ventilated areas. Ground equip-
ment, hoses, containers and objects being sprayed.

Avoid all ignition sources such as static electricity from plastic drop
cloths, open flames such as pilot lights, hot objects such as ciga-
rettes,  arcs from connecting or disconnecting power cords or turn-
ing light switches on and off.

Failure to follow this warning can result in death or serious injury.

NOTE: This is an example of the DANGER label on your sprayer. 

This label is available in other languages, free of charge. 
See page 28 to order.

Содержание PRO 301

































Отзывы: