background image

12 GAUGE

 INSTRUCTION MANUAL    17

SAFEGUArdiNG

WATER EXPOSuRE

Prior  to  exposing  the  timepiece  to  water,  ensure  both  crowns  are  pushed  fully  down  against  the  case  then  turn 

them clockwise to tighten their water seal. Rated at 10-bar hydrophobic, the timepiece may be worn during bathing, 

swimming and shallow diving. It is not designed for scuba or saturation diving. Do not pull out either crown or use the 

buttons if the timepiece is wet. If used in seawater, rinse the timepiece with fresh water and dry completely.

TEMPERATuRE

For precision timekeeping, normal operating temperature is 0°C to 50°C (32°F to 122°F).

MAGNETISM

Strong magnetic fields can have an adverse effect on the timepiece. Keep it away from magnetic objects.

CHEMICALS

The timepiece may become discolored or damaged if exposed to cosmetic spray, detergents, adhesives, solvents, 

or paints.

SHOCK WAVE

Although the timepiece resists shock damage, impact against a hard surface may cause damage to the movement 

or crystal.

PERIODIC MAINTENANCE

To ensure that the case, crowns, crystal seal, and gasket remain resistant to water exposure, it is recommended that 

the timepiece be inspected once every 2 to 3 years by an Authorized Oakley Service Center.

Содержание 12 GAUGE




















Отзывы: