O.S. engine MAX-32SX-H Series Скачать руководство пользователя | Manualshive

Страница: 11 / 32

background image

Fuel Can Filter

12V Battery

Starter

7 Fuel container filter
Install a filter on the outlet tube
of your refuelling container to
prevent entry of foreign matter
into the fuel tank

8 Silicone tubing
This is required for the
connection between the fuel
tank and engine.

9 Hexagon starting shaft
This shaft mounted on an
electric starting motor is driven
into the main body of a
helicopter to turn the engine.

Silicone tube

10 Electric starter and starter
battery
An electric starter is recom-
mended for starting.

FACTS ABOUT GLOWPLUGS

The role of the glowplug

Glowplug life

Particularly in the case of very high performance
engines, glowplugs must be regarded as expendable

With a glowplug engine, ignition is initiated by the
application of a 1.5-volt power source. When the
battery is disconnected, the heat retained within the
combustion chamber remains sufficient to keep the
plug filament glowing, thereby continuing to keep the
engine running. Ignition timing is 'automatic' : under
reduced load, allowing higher rpm, the plug becomes
hotter and, appropriately, fires the fuel/air charge
earlier; conversely, at reduced rpm, the plug become
cooler and ignition is retarded.

Since the compatibility of glowplug and fuel may have
a marked effect on performance and reliability, it may
be worthwhile to choose the R/C type plug found
most suitable after tests.Recommended O.S. plugs
are No.8, A5 and A3. Carefully install plug finger-tight,
before final tightening with the correct size plug
wrench.

10

«
...
9
10
11
12
13
...
»

Содержание MAX-32SX-H Series

































Отзывы:

Нет отзывов

Похожие инструкции для MAX-32SX-H Series

Бренд: O.S. engine Страницы: 5

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 19

IE3-K11R 132S 4 Ex e IIC T3

Бренд: VEM Страницы: 16

Бренд: RHINO MOTION CONTROLS Страницы: 4

Бренд: Tanaka Страницы: 10

Бренд: Vimar Страницы: 16

Бренд: Saito Страницы: 2

Бренд: Fabtex Страницы: 4

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 34

Бренд: O.S. engine Страницы: 40

Бренд: Mercury/Mariner Страницы: 130

Бренд: Mercury Страницы: 18

Бренд: Mercury Страницы: 9

Бренд: Mercury Страницы: 85

Бренд: MerCruiser Страницы: 895

116-BOXER IRS - V1.7

Бренд: MVVS Страницы: 6

Бренд: Mitsubishi Heavy Industries Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды