O.S. engine MAX-32SX-H Series страница 8 Скачать руководство пользователя | Manualshive

Страница: 8 / 32

background image

BASIC ENGINE PARTS

Heatsink Head

Carburetor
Typr 20C

Crankshaft

Propeller nut

Crankcase

Needle valve

Glowplug

Beam Mount

Recoil Starter
Assembly No.O

MAX-32SX-HX

Starter Handle

INSTALLING THE GLOWPLUG

Install washer on glowplug
and insert carefully into
cylinder-head, making sure
that it is not cross-threaded
before tightening firmly.

Glow plug

Washer

INSTALLATION

The under-surfaces of all O.S. engine beam
mounting lugs are precision machined flat and
exactyly parallel to the engine's horizontal axis. It is
essential that the engine mounts in the model are
also accurately made and aligned. If they are not,
they will cause stress and distortion within the engine
itself, probably resulting in loss of performance and
internal damage.
The recommended screws for securing the engine to
the engine mounts in the model are 3mm or 4-40
steel Allen type. It is also advisable to use lock
washers or LOCTITE to prevent nuts from loosening.

7

«
...
6
7
8
9
10
...
»

Содержание MAX-32SX-H Series

































Отзывы:

Нет отзывов

Похожие инструкции для MAX-32SX-H Series

Бренд: Isuzu Страницы: 174

Бренд: Lenze Страницы: 64

Бренд: Daedong Страницы: 51

Бренд: Jets Munt Страницы: 23

Бренд: Quectel Страницы: 37

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 24

Бренд: PYD Electrobombas Страницы: 36

Бренд: Briggs & Stratton Страницы: 17

Бренд: Briggs & Stratton Страницы: 16

Бренд: Roto Страницы: 9

Бренд: LinMot Страницы: 24

Бренд: LinMot Страницы: 30

Бренд: LinMot Страницы: 40

Бренд: Universal Страницы: 26

Бренд: M.T.H. Страницы: 47

Бренд: Iveco Страницы: 160

Бренд: HSD Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды