O.S. engine MAX-18CV-RM Скачать руководство пользователя

Страница: 14 / 20

TROUBLE SHOOTING

Symptom

Cause

Corrective action

Engine fails to fire.

Fuel tank is empty.
Fuel not reaching the engine.

Fill the tank with fuel and repeat
Priming procedure.

Glowplug element is burnt out.
Glowplug battery discharged

Replace glowplug.

Recharge or replace the battery.

Clogged fuel filter

Silencer inside is dirty.

Clean or replace fuel filter.

Clean inside the silencer.

Over priming

Remove glowplug and pump excess fuel.

Fuel tubing is disconnected.

Connect fuel tubing securely.

Fuel tubing is kinked, split or has a hole.

Check the tubing carefully and replace if necessary.

Incorrect servo linkage

Connect correctly after setting servo at neutral.

Reverse rotating direction of electric starter.

Mare sure it rotates counter clockwise seen
from crankshaft side.

Recoil starter slips.

Inject cleaner spray into starter cord crevis
on the body.

Symptom

Cause

Corrective action

Engine fires intermittently but does not run.

Insufficient fuel in the tank.

Fill the tank with fuel.

Deteriorated glowplug

Replace glowplug.

Clogged fuel filter

Silencer inside is dirty.

Clean or replace fuel filter.

Clean inside the silencer.

Engine overheated

Wait until engine cools.

Glowplug battery disconnected too soon.

Do not disconnect plug battery and wait until
r.p.m. become stable.

Air bubbles in fuel

Install O rings to the tank screws to
prevent bubbles.

Содержание MAX-18CV-RM





















Результаты поиска

Содержание MAX-18CV-RM

Отзывы:

Похожие инструкции для MAX-18CV-RM

Бренды по названию

Популярные бренды

O.S. engine MAX-18CV-RM, Инструкция пользователя

Результаты поиска

Содержание MAX-18CV-RM

Отзывы:

Похожие инструкции для MAX-18CV-RM

Бренды по названию

Популярные бренды