O.S. engine MAX-12TG Скачать руководство пользователя

Страница: 7 / 29

MAX-

12TG,

MAX-

12TG-P

Standard accessories

Engine Mount Spacer 1piece

Glow Plug No.8 1piece

Exhaust Seal Ring 1piece

MAX-

12TG-X,

MAX-

12TG-PX

Glow Plug No.8 1piece

Exhaust Seal Ring 1piece

INSTALLING THE
GLOWPLUG

Fit washer to glowplug and
insert carefully into cylinder-
head, making sure that it is
not cross-threaded before
tightening firmly.

Install the exhaust seal
ring supplied.

Exhaust
Seal Ring

Glowplug

Socket
Wrench

Washer

Use it when the engine interferes
with the car chassis.

CARBURETOR CONTROLS

The Needle-Valve(Adjusted at the factory):

Three adjustable controls are provided on this
carburetor.

For adjusting the mixture strength when the throttle
is fully open.

The Throttle Stop Screw
(Adjusted at the factory):

For setting the minimum idle speed:

For adjusting the mixture strength at part-throttle
and idle speed, to obtain steady idling and smooth
acceleration to mid speed.

The Metering Needle
(Adjusted at the factory):

NOTE: Readjustment may be necessary,
occasionally to allow for changes in fuel formula,
gear ratio or clutch engagement point.

Metering Needle

Throttle Stop
Screw

Needle Valve

Ball Link No.5

Dust Cover

Carburetor Type 12D

Fuel Inlet

Needle Holder

Содержание MAX-12TG






























Результаты поиска

Содержание MAX-12TG

Отзывы:

Похожие инструкции для MAX-12TG

Бренды по названию

Популярные бренды

O.S. engine MAX-12TG, Инструкция по эксплуатации

Результаты поиска

Содержание MAX-12TG

Отзывы:

Похожие инструкции для MAX-12TG

Бренды по названию

Популярные бренды