NXP Semiconductors S32R27 Скачать руководство пользователя | Manualshive

Страница: 5 / 50

background image

Table 5. Supply pin decoupling capacitors (continued)

Domain name

Supply

Voltage

Minimum Decoupling Capacitors

VDD_HV_RAW

3.3 V

0.1 μF, 1 μF

3.3 V

1000 pF, 0.1 μF, 1 μF

VDD_HV_ADC

3.3 V

0.1 μF, 1 μF

VDD_HV_ADCREF0/2

3.3 V

0.01 μF, 1 μF

VDD_HV_IO_PWM

3.3 V

2x 0.1 μF for each supply

VDD_HV_FLA

3.3 V

0.1 μF, 1000 pF

VDD_HV_PMU

3.3 V

100 nF, 4.7 μF

VDD_HV_REG3V8

3.13 V - 5.5

V

1 μF Ceramic

VDD_LV_DRFPLL

1.25 V

1000 pF, 0.1 μF, 1 μF, 0.01 μF

VDD_LV_IO_AURORA

1.25 V

0.1 μF, 1 μF

VDD_LV_PLL0

1.25 V

1000 pF, 0.1 μF, 1μF, 0.01 μF

VDD_LV_DPHY

1.25 V

Ferrite bead, >5 μF, 100 nF, 1000 pF

1. When using internal regulation mode, assure that the total capacitance (accounting for temperature variations) never falls

below 40 μF

2. External capacitors for the IO pins are dependent on the application.
3. Not present on S32R372 141BGA Package
4. When device is configured in external regulation mode and supply is connected to VDD_HV_PMU. For internal regulation

mode see

SMPS external component configuration

The device has several pins for the connection to external decoupling capacitors for the analog front-end. Details of these can
be found in

RADAR analog front end

3.2 Decoupling capacitors layout priority

When trade-offs must be made in the schematic layout, it is important to ensure that the highest priority supplies have
decoupling capacitors placed as closely as possible to the MCU. The list below outlines the recommended order of the
supplies from highest to lowest priority in terms of their importance for decoupling.

1. VDD_HV_RAW & VDD_HV_DAC
2. VDD_HV_ADCREF0/2
3. VDD_HV_ADC
4. VDD_LV_PLL0
5. VDD_LV_DPHY
6. VDD_LV_CORE
7. VDD_LV_AURORA
8. VDD_HV_PMU
9. VDD_HV_FLA

10. VDD_LV_LFASTPLL

11. VDD_LV_IO
12. VDD_HV_PWM

13. VDD_HV_IO

2. Not present on S32R372 141MAPBGA Package
3. Not present on S32R372 141MAPBGA Package

Power supply

S32R27/37 Hardware Design Guide, Rev. 1, 04/2018

NXP Semiconductors

5

«
...
3
4
5
6
7
...
»

Содержание S32R27



















































Отзывы:

Нет отзывов

Похожие инструкции для S32R27

Бренд: Paratec Страницы: 8

Бренд: J+J Страницы: 33

Бренд: bluelab Страницы: 39

MOBA-Matic MMC-1000

Бренд: MOBA Страницы: 172

Бренд: Velleman-Kit Страницы: 32

Бренд: Instruments of Things Страницы: 12

Бренд: National Instruments Страницы: 20

Бренд: Eliweli Страницы: 2

Бренд: Yaesu Страницы: 12

Бренд: Oase Страницы: 646

Бренд: Sensibo Страницы: 15

Universal CapSense CY3280-22x45

Бренд: Cypress Страницы: 55

UltraVista 4K VWL-T122-4K-DP

Бренд: Rose electronics Страницы: 28

RMC-RRS011-HE01

Бренд: WAVESTREAM Страницы: 54

QMatrix QT60486

Бренд: Quantum Research Group Страницы: 11

Бренд: Vestax Страницы: 4

BatteryMINDer SCC515

Бренд: VDC Electronics Страницы: 8

Door Cloud Zone spot

Бренд: Spica Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды