background image

Safety Information

MC1320x RF Daughter Card, Rev. 1.2

Freescale Semiconductor

3

 

2

Safety Information

Any modifications to this product may violate the rules of the Federal Communications Commission and 
make operation of the product unlawful.

47 C.F.R. Sec. 15.21

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant 
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the instructions, may cause harmful interference 
to radio communications. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference to radio or television reception, which can 
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.

Consult the dealer or an experienced radio/TV technician for help.

47 C.F.R. Sec.15.105(b)

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 
The antenna(s) used for this equipment must be installed to provide a separation distance of at least 8 
inches (20cm) from all persons.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired 
operation.

3

Revision History

The following table summarizes revisions to this document since the previous release (Rev 1.1).

Revision History

Location

Revision

Section 6

Updated document cross reference.

Содержание MC1320 Series

















Отзывы: