NXP Semiconductors LPC5410x Скачать руководство пользователя | Manualshive

Страница: 315 / 463

background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016

316 of 464

NXP Semiconductors

UM10850

Chapter 23: LPC5410x I2C-bus interfaces (I2C0/1/2)

23:20 -

Reserved. Read value is undefined, only zero should be written.

NA

NA

24

EVENT
TIMEOUT

Event Time-out Interrupt flag. Indicates when the time between events has
been longer than the time specified by the TIMEOUT register. Events include
Start, Stop, and clock edges. The flag is cleared by writing a 1 to this bit. No
time-out is created when the

I

2

C

-bus is idle.

0

W1

0

No time-out. I

2

C bus events have not caused a time-out.

1

Event time-out. The time between I

2

C bus events has been longer than the

time specified by the I2C TIMEOUT register.

25

SCL
TIMEOUT

SCL Time-out Interrupt flag. Indicates when SCL has remained low longer
than the time specific by the TIMEOUT register. The flag is cleared by writing
a 1 to this bit.

0

W1

0

No time-out. SCL low time has not caused a time-out.

1

Time-out. SCL low time has caused a time-out.

31:26 -

Reserved. Read value is undefined, only zero should be written.

NA

NA

Table 344. I

2

C Status register (STAT, address offset 0x004) bit description

…continued

Bit

Symbol

Value Description

Reset

value

Access

Table 345. Master function state codes (MSTSTATE)

MST
STATE

Description

Actions

DMA
allowed

0x0

Idle.

The Master function is available to be used for a new

transaction.

Send a Start or disable MSTPENDING
interrupt if the Master function is not
needed currently.

No

0x1

Received data is available (Master Receiver mode).

Address

plus Read was previously sent and Acknowledged by slave.

Read data and either continue, send a
Stop, or send a Repeated Start.

Yes

0x2

Data can be transmitted (Master Transmitter mode).

Address

plus Write was previously sent and Acknowledged by slave.

Send data and continue, or send a
Stop or Repeated Start.

Yes

0x3

Slave NACKed address.

Send a Stop or Repeated Start.

No

0x4

Slave NACKed transmitted data.

Send a Stop or Repeated Start.

No

Table 346. Slave function state codes (SLVSTATE)

SLVSTATE

Description

Actions

DMA
allowed

0

SLVST_
ADDR

Address plus R/W
received.

At least one of the

4 slave addresses has been
matched by hardware.

Software can further check the address if needed, for instance if
a subset of addresses qualified by SLVQUAL0 is to be used.
Software can ACK or NACK the address by writing 1 to either
SLVCONTINUE or SLVNACK. Also see

regarding

10-bit addressing.

No

1

SLVST_RX

Received data is available
(Slave Receiver mode).

Read data, reply with an ACK or a NACK.

Yes

2

SLVST_TX

Data can be transmitted
(Slave Transmitter mode).

Send data. Note that when the Master NACKs dat transmitted by
the slave, the slave becomes de-selected.

Yes

«
...
313
314
315
316
317
...
»

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

Бренд: Koer Страницы: 6

Бренд: D+H Страницы: 32

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

Бренд: Quantum Страницы: 20

Бренд: W.E.ST. Страницы: 34

Бренд: Ltech Страницы: 4

Бренд: Motor Guard Страницы: 2

Бренд: rotork Страницы: 22

Бренд: HIKVISION Страницы: 5

Бренд: Nexen Страницы: 28

Бренд: WAGO Страницы: 44

Бренд: Eaton Страницы: 12

Бренд: salmson Страницы: 37

Бренд: Martin Audio Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды