manualshive.com logo in svg

NXP Semiconductors LPC5410x, Руководство пользователя

Микроконтроллеры NXP Semiconductors LPC5410x - мощные устройства для встроенных систем. Инструкция пользователя доступна для свободного скачивания на manualshive.com. Получите полный контроль над вашим устройством, загрузив бесплатный руководство пользователя.

Поделиться
Скачать
background image

UM10850

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2016. All rights reserved.

User manual

Rev. 2.4 — 13 September 2016 

331 of 464

NXP Semiconductors

UM10850

Chapter 23: LPC5410x I2C-bus interfaces (I2C0/1/2)

–

as a slave transmitter, after each after each data byte is sent and the matching 
acknowledge is received from the master

In each case, the relevant pending flag (MSTPENDING or SLVPENDING) is set at the 
point where clock stretching occurs.

23.7.2 Time-out

A time-out feature on an I

2

C interface can be used to detect a “stuck” bus and potentially 

do something to alleviate the condition. Two different types of time-out are supported. 
Both types apply whenever the I

2

C block and the time-out function are both enabled. 

Master, Slave, or Monitor functions do not need to be enabled.

In the first type of time-out, reflected by the EVENTTIMEOUT flag in the STAT register, the 
time between bus events governs the time-out check. These events include Start, Stop, 
and all changes on the I

2

C clock (SCL). This time-out is asserted when the time between 

any of these events is longer than the time configured in the TIMEOUT register. This 
time-out could be useful in monitoring an I

2

C bus within a system as part of a method to 

keep the bus running of problems occur.

The second type of I

2

C time-out is reflected by the SCLTIMEOUT flag in the STAT 

register. This time-out is asserted when the SCL signal remains low longer than the time 
configured in the TIMEOUT register. This corresponds to SMBus time-out parameter 
T

TIMEOUT

. In this situation, a slave could reset its own I

2

C interface in case it is the 

offending device. If all listening slaves (including masters that can be addressed as 
slaves) do this, then the bus will be released unless it is a current master causing the 
problem. Refer to the SMBus specification for more details.

Both types of time-out are generated only when the I

2

C bus is considered busy, i.e. when 

there has been a Start condition more recently than a Stop condition.

23.7.3 Ten-bit addressing

Ten-bit addressing is accomplished by the I

2

C master sending a second address byte to 

extend a particular range of standard 7-bit addresses. In the case of the master writing to 
the slave, the I

2

C frame simply continues with data after the 2 address bytes. For the 

master to read from a slave, it needs to reverse the data direction after the second 
address byte. This is done by sending a Repeated Start, followed by a repeat of the same 
standard 7-bit address, with a Read bit. The slave must remember that it had been 
addressed by the previous write operation and stay selected for the subsequent read with 
the correct partial I

2

C address.

For the Master function, the I

2

C is simply instructed to perform the 2-byte addressing as a 

normal write operation, followed either by more write data, or by a Repeated Start with a 
repeat of the first part of the 10-bit slave address and then reading in the normal fashion.

For the Slave function, the first part of the address is automatically matched in the same 
fashion as 7-bit addressing. The Slave address qualifier feature (see 

Section 23.6.14

) can 

be used to intercept all potential 10-bit addresses (first address byte values F0 through 
F6), or just one. In the case of Slave Receiver mode, data is received in the normal 
fashion after software matches the first data byte to the remaining portion of the 10-bit 
address. The Slave function should record the fact that it has been addressed, in case 
there is a follow-up read operation.

Содержание LPC5410x
















































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LPC5410x

Panasonic FP2 Series Technical Manual preview
FP2 Series
Бренд: Panasonic Страницы: 68
Panasonic FP0H Series Operation Manual preview
FP0H Series
Бренд: Panasonic Страницы: 20
Unipulse F160 Operation Manual preview
F160
Бренд: Unipulse Страницы: 99
Mainpine EPC Operating Instructions Manual preview
EPC
Бренд: Mainpine Страницы: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Бренд: Danfoss Страницы: 20
GAUGEMASTER COMBI Manual preview
COMBI
Бренд: GAUGEMASTER Страницы: 2
EasyIO FC Series Firmware Upgrade User Manual preview
FC Series
Бренд: EasyIO Страницы: 19
PAC 212 Install Manual preview
212
Бренд: PAC Страницы: 17
Gardena Master Operator'S Manual preview
Master
Бренд: Gardena Страницы: 18
Danfoss VLT Micro Drive FC 51 Series Quick Manual preview
VLT Micro Drive FC 51 Series
Бренд: Danfoss Страницы: 23
Garmin TR-1 Gold Installation Instructions preview
TR-1 Gold
Бренд: Garmin Страницы: 4
Eaton LS Series Instruction Leaflet preview
LS Series
Бренд: Eaton Страницы: 2
Talgil DREAM 2 Manual preview
DREAM 2
Бренд: Talgil Страницы: 14
Vaillant VRT 350f Installation Instructions Manual preview
VRT 350f
Бренд: Vaillant Страницы: 36
Vaillant VRT 350 Installation Instructions Manual preview
VRT 350
Бренд: Vaillant Страницы: 28
Vaillant VAZ CPC Operating Instructions Manual preview
VAZ CPC
Бренд: Vaillant Страницы: 92
Eaton EZD Series User Manual preview
EZD Series
Бренд: Eaton Страницы: 448
POLA HP49 Handbook preview
HP49
Бренд: POLA Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды