background image

KIT34704BEPEVBE Evaluation Board

, Rev 1.0

Freescale Semiconductor

3

Important Notice

2

Important Notice

Freescale provides the enclosed product(s) under the following conditions:
This evaluation kit is intended for use of ENGINEERING DEVELOPMENT OR EVALUATION PURPOSES ONLY. It 
is provided as a sample IC pre-soldered to a printed circuit board to make it easier to access inputs, outputs, and 
supply terminals. This EVB may be used with any development system or other source of I/O signals by simply 
connecting it to the host MCU or computer board via off-the-shelf cables. This EVB is not a Reference Design and is 
not intended to represent a final design recommendation for any particular application. Final device in an application 
will be heavily dependent on proper printed circuit board layout and heat sinking design as well as attention to supply 
filtering, transient suppression, and I/O signal quality. 
The goods provided may not be complete in terms of required design, marketing, and or manufacturing related 
protective considerations, including product safety measures typically found in the end product incorporating the 
goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate 
precautions with regard to electrostatic discharge. In order to minimize risks associated with the customers 
applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or 
procedural hazards. For any safety concerns, contact Freescale sales and technical support services.
Should this evaluation kit not meet the specifications indicated in the kit, it may be returned within 30 days from the 
date of delivery and will be replaced by a new kit.
Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no 
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does 
Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims 
any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and 
do vary in different applications and actual performance may vary over time. All operating parameters, including 
“Typical”, must be validated for each customer application by customer’s technical experts.
Freescale does not convey any license under its patent rights nor the rights of others. Freescale products are not 
designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or 
other applications intended to support or sustain life, or for any other application in which the failure of the Freescale 
product could create a situation where personal injury or death may occur. 
Should Buyer purchase or use Freescale products for any such unintended or unauthorized application, Buyer shall 
indemnify and hold Freescale and its officers, employees, subsidiaries, affiliates, and distributors harmless against 
all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim 
of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that 
Freescale was negligent regarding the design or manufacture of the part.Freescale™ and the Freescale logo are 
trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective 
owners. © Freescale Semiconductor, Inc. 2008

Содержание KIT34704BEPEVBE








































Отзывы: