nvent SPECTRACOOL Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 36

background image

© 2018 nVent

89091001

- 29 -

8.

Hoffman A.C. Monitor Data Logging

The Hoffman A.C. Monitor can be configured to log sensor data from one or more ACUs into a sensor

data file. The sensor data file can then be opened in Excel for analysis.

8.1 Configuring an ACU for Data Logging

To configure an ACU for data logging, click “Tools” menu and select “Change Multiple ACU

Configuration” from the pull-down menu. Then click Setup button.

Find the ACU you would like to configure, click on the “Data Logging” column cell to change the

“No” to “Yes”, and, finally, click “Save Configuration File”. Repeat this for each ACU that you would

like to configure an ACU for data logging.
When clicking on “Enable Polling” button, the sensor data for each ACU that was configured for

data logging will be stored in an XML file.

«
...
27
28
29
30
31
...
»

Содержание SPECTRACOOL





































Отзывы:

Нет отзывов

Похожие инструкции для SPECTRACOOL

ServeRAID M5014

Бренд: IBM Страницы: 106

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

Бренд: K1EL Страницы: 46

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Vageo Страницы: 2

8745 MFC Ethernet

Бренд: Burkert Страницы: 70

Series RHCN-7000

Бренд: Omega Engineering Страницы: 2

Бренд: WAM Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: TDSi Страницы: 71

Бренд: Azbil Страницы: 68

Бренд: Ltech Страницы: 2

Бренд: Tapeswitch Страницы: 2

Бренд: Botex Страницы: 36

Бренд: National Instruments Страницы: 18

IC 912 Pt100-TC

Бренд: Eliwell Страницы: 4

Бренд: Atmel Страницы: 150

Бренд: ECO POWER Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды