nvent RAYCHEM HWT-P Скачать руководство пользователя страница 5

Страница: 5 / 6

Cold
water in

HWAT water
heater tag

Mixing
valve

Tempered
water out

Hot water out

Hot water in

Water
heater

014

ent

W.n

Ven

t.CO

PN P

000001655 H59088 0

2/1

For H

T Systems install this tag on

the hot water heater or temper

atur

e contr

ol v

alve

ser

vicing the hot water systems.

ATTEN

TION

150°F

DO NO

T heat water abo

ve 150°F

. Temper

atur

abo

ve 150°F

will permanently r

educe the power

output of the HW

AT heating cable used on this hot

water system.

Ground wire

Red wire nuts

(Item H)

Gray wire nut

(Item I)

• Apply warning label

(Item G) to junction

box cover.

• Use red wire nuts

(Item H) to connect

the supply with the

heating cable bus

wires.

• Use gray wire nut

(Item I) to connect

the ground braid to

the supply ground.

• Attach HWAT water heater tag

(Item A) to either the water

heater or temperature control

valve servicing the hot water

systems, using the plastic cable

tie (Item N).

nVent.com | 5

Содержание RAYCHEM HWT-P







Результаты поиска

Содержание RAYCHEM HWT-P

Отзывы:

Похожие инструкции для RAYCHEM HWT-P

Бренды по названию

Популярные бренды

nvent RAYCHEM HWT-P, Руководство по установке

Результаты поиска

Содержание RAYCHEM HWT-P

Отзывы:

Похожие инструкции для RAYCHEM HWT-P

Бренды по названию

Популярные бренды