Nuvair Voyager IV Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 40

Nuvair Voyager IV Скачать руководство пользователя страница 20

Voyager IV

Nitrox System

Nuvair www.nuvair.com

Page

20

HP

Compressor
Oil Pressure

13.4 Check Compressor Lubricant Levels

Check lubricant levels before starting fill operations and add lubricant as required. Use only the
lubricants specified.

*To read LP oil level, turn the LP Compressor knob to Start position, then

immediately to the Off position. This will cycle the LP Compressor, distributing oil throughout the
system so an accurate reading may be made.

Do not allow Nitrox to be discharged into the air storage system. Nitrox
introduced into the air storage system could cause a diver to suffer from oxygen
poisoning at depth. Oxygen poisoning is extremely dangerous and can lead to

death by drowning.

Do not allow air to be discharged into the Nitrox storage system. Air introduced into the Nitrox
storage system could cause a diver to suffer decompression sickness if the Nitrox mixture is
not analyzed properly and is used underwater under the assumption it is a different mix.

13.5 Control Panel Controls

Compressor

Lubricant

Level Sight

Gauges

Check Oil

Level*

Cabinet

Temperature

Gauge

Feed Air

Pressure

Gauge

LP

Compressor

Oil

Temperature

Heater

Temperature

Gauge

Fill

Pressure

Gauge

On/Off

Switches

LP Feed Air

Regulator

Adjustment

Knob

Stage

Pressure

Gauges

O

2

Analyzers

«
...
18
19
20
21
22
...
»

Содержание Voyager IV









































Отзывы:

Нет отзывов