Nuvair Pro CO2 Analyzer Скачать руководство пользователя страница 16

Страница: 16 / 20

Pro CO

Carbon Dioxide Analyzer

NUVAIR Rev.02.14.12

Page

Pro CO

Carbon Monoxide Analyzer Manual

9.0 Spares and Accessories

9.1. Sensors

Sensor replacement for Pro CO

9.2. Calibration Equipment

Calibration check requires certified CO

calibration gas

to be delivered at a specific flow rate and pressure.

A variety of calibration gas canisters are available from
Nuvair, with compatible Flow Restrictor/ Regulator
assemblies to regulate the gas.

10.0 Troubleshooting

SYMPTOM

REASON

SOLUTION

Battery symbol

Low Battery

Change the battery

No display

Switched off
Bad connection
Low Battery

Switch on
Check display/ battery connection
Change the battery

Reading erratic

Pressure on sensor
Radio transmission
Sensor old or faulty
Condensation on sensor.

Check flow
Move unit away
Change sensor
Dry in air

Display segments missing

Display faulty

Return to dealer

Reading drifts

Rapid temperature change

Stabilize temperature & recalibrate

Flow Restrictor/

Regulator
Assembly

Nuvair

Calibration Gas

Specs:

CO 10 ppm

CO2 1000 ppm

Nitrogen Balance

Содержание Pro CO2 Analyzer




















Результаты поиска

Содержание Pro CO2 Analyzer

Отзывы:

Похожие инструкции для Pro CO2 Analyzer

Бренды по названию

Популярные бренды

Nuvair Pro CO2 Analyzer, Руководство по эксплуатации

Результаты поиска

Содержание Pro CO2 Analyzer

Отзывы:

Похожие инструкции для Pro CO2 Analyzer

Бренды по названию

Популярные бренды