background image

www.NutrichefKitchen.com

12

5. Step Selection

     When the machine in standby or pause state, every time when pressing "

STEP

" button, the selected  

     STEP symbol will be blink in order on the screen, thus the power (wattage), temperature and timing  
     corresponding to the selected STEP can be set. You can also press the "

RUN/PAUSE

" key to RUN the  

     program backwards from the selected step. Program I can choose any step from all the step of S - L,  
     program II can choose any step from B1 to B3, program III can choose any step from all steps of S - B3.

6. Setting of power, temperature and timing

     When the machine in standby or suspended state, press "

STEP

" to select a step and reset the setting of  

     power, temperature and timing corresponding to this step.
     Every time to press "

SET

" button, the setting will follow below order to cycle, the icon corresponding  

     the selected symbol will blink, and then press (+) and (-) button to reset the value.

7. Restore default factory settings

     In the standby or pause state, keep press "

PROG

" button for 5 seconds to restore the factory settings,  

     the previous set procedures and settings will be eliminated from the machine. 
     

Note:

 in general, if the settings are wrong and memory or program is out of order, you can pause at  

     first and then restore the factory settings.

8. Adjustment of temperature deviation (temperature compensation function)

     In standby or pause state, keep press "

°C/°F

" button for 5 seconds to enter the function of temperature  

     deviation adjustment. Pressing (+) and (-) button to modify the temperature deviation. 
     After determining the value, press the SET button to save the settings. 
     The range of this deviation adjustment is within ±10°C.

Note:

 

1. This adjustment function is required in winter when the external environment temperature is too low,  
     the heat loss is too fast, or the water is boiling due to the high altitude, and the temperature cannot  
     reach 100°C/212°F  to enter the later program. 
2. If it is found that there is a big error between the display temperature and the measured temperature  
     during the course of using, the value can be adjusted and corrected through this function.

9. Conversion between Celsius and Fahrenheit °F

     Press "

°C/°F

" button at any time after starting up to convert the display of °C and Fahrenheit °F.

10. Power off protection function

     If there is an unexpected power failure after starting up, the machine will automatically remember the  
     breakpoint. When the power is switched on again, the breakpoint will be automatically found by the  
     machine. Press the "

RUN/PAUSE

" button to restart this step and continue to RUN the next step as    

     previous settings.

Temperature           Timing           Power

Содержание PKBRKTL200

















Отзывы: