Nupower EVOLUTION NPE136, Руководство пользователя

Страница: 16 / 60

15
GB
COMPONENTS AND CONTROLS (PIC. A)
ATTACHING SANDPAPER (PIC.1)
Select an abrasive paper with the correct grit corresponding to
the work to be carried out.
WARNING! Always disconnect the machine from the
power supply before adjustment, changing accessories and
maintenance. The abrasive side of the paper faces outwards
from the base plate. Locate the clamps on either side of the
machine (
Pic.1.1 ). Push the clamp lever inwards to clear the
securing tag. The lever is under spring tension. Allow the lever
to raise upwards and then manoeuvre outwards and downwards
( Pic.1.2 ). This allows the clamp to release its grip on the sander
base. Repeat the operation for other side. Position one end of
the sand paper under the clamp and re-secure.
The sand paper should be pulled taught and follow the contours
of the Sander base. Ensure alignment of dust extraction holes
with the holes in the sandpaper sheets. Position the other end
of the sand paper under the clamp and re-secure.
The Sander is now ready for operation.
CONTINUOUS RUNNING SWITCH (PIC.2)
This machine is fitted with a “continuous running switch”
(
Pic.2.1 ). To start the machine squeeze the ON / OFF trigger
( Pic.2.2 ). When the machine starts press in the “continuous
running button ( Pic.2.1 ) located on the side of the handle,
release the ON / OFF trigger. The machine will now run
continuously without the need to maintain pressure on the ON
/ OFF trigger. To stop the machine briefly squeeze then release
the ON / OFF trigger.
DUST EXTRACTION
This machine is supplied with a dust extraction facility. The two
dust extraction adapters will allow the Sander to be connected
to most vacuum cleaner hoses. We recommend the use of this
facility at all times, especially when sanding medium density
fibre board (M.D.F).
SPECIFIC SAFETY INSTRUCTIONS
WARNING! TWO HANDED OPERATION REQUIRED
This machine requires the use of two hands to ensure safe
operation and should not be used when working from ladders
and step ladders.
If the machine is to be used when working at height a suitable,
stable platform or scaffold tower with hand rails and kick boards
should be used.
WARNING!
Extreme Caution Required
Extreme care should be taken when sanding paint. The dust
residue may contain
LEAD which is poisonous. Any pre 1960
building may have paint containing lead on wood or metal
surfaces which has been covered with additional layers of
paint.
STOP!
If you suspect that paint on surfaces in your house contains
lead seek professional advice.
Lead based paints should only be removed by a professional
and should not be removed using a Sander. Once deposited on
surfaces, hand to mouth contact can result in the ingestion of
lead. Exposure to even low levels of lead can cause irreversible
brain and nervous system damage. The young and unborn
children are particularly vulnerable.
WARNING!
Some wood and wood type products especially MDF (Medium
Density Fibreboard) can produce dust that can be hazardous to
your health. We recommend the use of an approved face mask
with replaceable filters when using this machine in addition to
using the dust extraction facility.
Ensure that the holes in the sanding sheet align with the holes
in the machine sanding pad.
Ensure that the sanding sheet is securely retained under the
sanding sheet clamps and that the sanding sheet is taught.
Do not start the machine whilst it is in contact with the work
piece.
Check the work piece for any protruding nails, screw heads or
anything that could tear or damage the sanding sheet.
Hold the machine correctly using two hands and adopt a stable
stance, make sure that the mains cable is prevented from
coming into contact with the machine or getting caught up on
other objects preventing completion of the sanding pass.
Replace the sanding sheet as soon as it becomes worn or if it is
torn. Torn sanding sheets can cause deep scratches which are
difficult to remove.
Always start sanding with coarse grade of sanding sheet
working through the grades to the finest grade.
Wherever possible always sand in the direction of the grain
and remove the sanding dust between each grade of sanding
sheet.
Do not use this sander for sanding Gyproc™ or Gyproc™ type
products.
TIP
An acceptable filler which could be a good colour match can be
made by mixing the sanding dust with PVA glue.
1 Front grip
2 Machine identification plate
3
On/Off trigger
4
Continuous running button
5 Main grip
6 Sandpaper
7
Vibrating plate
8
Clamping device
9 Vacuum cleaner adapters
10 Electrical cord