manualshive.com logo in svg

NuAire NU-5500, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
NuAire NU-5500 Скачать руководство пользователя страница 16

OM0133 

15 

 

7.6 

Air Pump Assembly Shipping Foam: One or more blocks of

 

foam is used to secure the air pump 

during shipping. 

 

IMPORTANT:

  

FOAM BLOCK MUST BE REMOVED BEFORE OPERATION 

 

To remove foam block: 

1. 

Remove control center cover by unscrewing the (4) screws holding it to the top of the 
Incubator.  Lift the cover straight up and set it aside. 

 

2. 

Remove the foam block from under the air pump allowing the pump to hang freely in the 
mounting bracket.  It is located to the right of the chamber blower motor on the right side 
of the Incubator. 

 

3. 

Reinstall the control center cover on top of the Incubator and secure it with the screws 
removed in Step 1. 

 

NOTE: Foam block can be removed through the front control panel.  Remove the 2 locking screws 
(one each) either side of the control center lid.  Open the outer door and the control panel will 
swing down and open. 

 

7.7 Water 

Pan 

Place water pan in the center on the bottom of the chamber and fill with Single distilled water no purer 
than 1 Mega Ohm.  It is recommended to fill the pan to about 1/2 inch below the top rim.  See Sections 
3.1 and 8.2 for more specifications and operational details. 

 

7.8 

Stacking Units: Refer to BCD-09404 in the ASSEMBLY Section 

Align the feet of the top Incubator with the indentations in the lid of the bottom Incubator.  Ensure that 
there is a minimum of 1/4 inch (6mm) air gap between the Incubators as explained in section 7.2 to avoid 
obstructing the cabinet air flow.  Secure the stacking straps that are attached to the bottom of the top 
Incubator to the lid of the bottom Incubator using the 4 screws that secure the lid.  Only stack units 2 
high. 

 

7.9 Correct 

Installation 

When the Incubator is installed correctly connected to the power source it is rated for gas connections 
made properly, the water pan filled, the shelves in place, and the unit is leveled.  Read section 8 and 
follow all instructions for setting set points at the desired value.  Then calibrate the Incubator control 
systems as explained in section 9.  If the Incubator is installed and calibrated correctly it will meet the 
performance specifications listed in section 3.2. 

 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание NU-5500























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды