NuAire DE1-ES Скачать руководство пользователя страница 5

5

22. 02. 22. Document Number  611280

Nuaire | Western Industrial Estate | Caerphilly | CF83 1NA | nuaire.co.uk

DAVE Extract (DE)

Installation Manual

6.3 Electrical Connections

6.3.1 Mains Connections

Mains cables should be suitably sized and terminated at the terminals 
shown on the appropriate diagram.

6.3.2 Control Connections

3 IDC plug-in Net connectors are provided for the connection of 
compatible sensors, manual controls and for linking the fans together 
under a common control. If more than 3 connections are required, 
the junction box (product code ES-JB) should be used (see data cable 
installation).

Ecosmart Net Connections

6.3.3 Switched Live (SL) Terminal

Mains cables should be suitably sized and terminated at the terminals 
shown on the appropriate diagram.

N

E

L

SL

Remove link if switched live signal, 
an enabler or BMS signal is connected.

Terminals or PCB

Mains connection pre-wired
230V 50Hz 1ph / 220V 60Hz 1ph

SL Terminal

6.3.4 Control Connections

A signal of 100-230V / 220V a.c. will activate the fan from either its 
off state or trickle state (see setting to work-trickle switch). When 
the SL is disconnected the fan will over-run (see setting to work-timer 
adjustment). 

Do not take this signal from an isolating transformer.

6.3.5 Volt Free Relay Contacts

Volt free contacts are not fused, if these are used to power any external 
equipment, the installer must provide adequate fusing or other 
protection. These contacts are rated at 5A resistive, 0.5A inductive.

Run Connections =

 Contacts are closed when the fan is running. 

Fault Connections - No Fault =

 Contacts are closed. 

Fault Connections - Fault =

 Contacts are open.

Volt Free Relay Contacts

RUN 

FAULT

Run signal    Fault signal

6.3.6 Data Cable Installation

A 4-core SELV data cable is used to connect devices. 
Do not run data cable in the same conduit as the mains cables and 
ensure there is a 50mm separation between the data cable and other 
cables. The maximum cable run between any two devices is 300m 
when it is installed in accordance with the instructions.

Please note that the total data cable length used in any system 
must be less than 1000m. Keep the number of cable joints to a 
minimum to ensure the best data transmission efficiency between 
devices.

6.3.7 Maximum Number of Devices

The maximum number of devices (including fans) that can be 
connected together via the cable is 32, irrespective of their functions.

6.3.8 Other Low Voltage Cables

Follow the basic principle (as 5.1.6). Keep the cable run as short as 
possible, less than 50 metres.

6.3.9 Commissioning Panel Details

A Commissioning Procedure document (leaflet No. 671153) is available 
on request from the Nuaire Technical Library, Tel: 029 2088 5911.

LED indicators

Min 

Max  SL run on

Trickle

Test

1

0        

Pwr
Standby
Fan 1 
Fan 2 
Heating
Cooling
Fault
Frost
Tx
Rx

MIN 

=  Minimum speed
  adjustment

MAX 

=  Maximum speed
  adjustment

SL Run on  =  Switched Live Run-On

  Timer adjustment

TRICKLE 

 =  Selects trickle running:

  0 = off, 1 = selected

TEST 

=  Test button

10 

Commissioning Panel

6.4 LED Indicator

PWR

  

GREEN: Power on & OK.  

 

RED: To much power is taken by peripherals or there is a short  

 

circuit in the net cable. Check the cable and use a junction    

 

box (ES-JB) to connect some of the peripherals. 

Standby

  LED on when fan is not running. 

Fan 1  

GREEN: Fan 1 is running, RED: Fan 1 faulty. 

Fan 2

  

GREEN: Fan 2 is running, RED: Fan 2 faulty (Twinfan only). 

Heating* 

Not applicable. See note. 

Cooling*

  Not applicable. See note. 

Fault 

 

LED on when a fault is present on unit. 

Frost*

  Applicable with LPHW only. See note. 

Tx 

 

LED on when the controller is transmitting data. 

Rx 

 

LED on when the controller is receiving data.

The control panel is common to all the Ecosmart classic products 
and will have indicators for functions that are not available in this 
particular fan. However these indicators will not be illuminated.

Содержание DE1-ES









Отзывы: